Z-Wave Application Specification

Table of Contents

• 1. Introduction
  • 1.1. Disclaimer
  • 1.2. Purpose
  • 1.3. Audience and Requirements
  • 1.4. Terms
  • 1.5. Terminology And Abbreviations
• 2. Application Command Classes
  • 2.1. Command Class Overview
    • 2.1.1. Overview
    • 2.1.2. Command class format
      • 2.1.2.1. Frame format
        • 2.1.2.1.1. Command class
        • 2.1.2.1.2. Command
        • 2.1.2.1.3. Command data (N bytes)
      • 2.1.2.2. Command class versioning
    • 2.1.3. Controlled and Supported Command Classes
    • 2.1.4. Node Information Frame
      • 2.1.4.1. Z-Wave Protocol Specific Part
      • 2.1.4.2. Application Specific Part
      • 2.1.4.3. NIF and Multi Channel/Security Command Classes
        • 2.1.4.3.1. Examples
      • 2.1.4.4. Command Class specific NIF rules
    • 2.1.5. Multicast and broadcast commands
    • 2.1.6. Actuator Control
      • 2.1.6.1. Terminology
      • 2.1.6.2. Reporting values
      • 2.1.6.3. Command values vs. hardware values
      • 2.1.6.4. Supporting multiple actuator Command Classes
    • 2.1.7. Common fields and encoding
      • 2.1.7.1. Reserved and Res fields
      • 2.1.7.2. Reserved values and reserved bits
      • 2.1.7.3. Duration encoding
      • 2.1.7.4. Unsigned encoding
      • 2.1.7.5. Signed encoding
      • 2.1.7.6. Fields values and version
  • 2.2. Command Class Definitions
    • 2.2.1. Active Schedule Command Class, version 1
      • 2.2.1.1. Terminology
        • 2.2.1.1.1. Targets
        • 2.2.1.1.2. Schedules
        • 2.2.1.1.3. Schedule Enabled Definitions
        • 2.2.1.1.4. Schedule Metadata
      • 2.2.1.2. Compatibility Considerations
      • 2.2.1.3. Active Schedule Capabilities Get Command
      • 2.2.1.4. Active Schedule Capabilities Report Command
      • 2.2.1.5. Active Schedule Enable Set Command
      • 2.2.1.6. Active Schedule Enable Get Command
      • 2.2.1.7. Active Schedule Enable Report Command
      • 2.2.1.8. Active Schedule Year Day Schedule Set Command
      • 2.2.1.9. Active Schedule Year Day Schedule Get Command
      • 2.2.1.10. Active Schedule Year Day Schedule Report Command
      • 2.2.1.11. Active Schedule Daily Repeating Schedule Set Command
      • 2.2.1.12. Active Schedule Daily Repeating Schedule Get Command
      • 2.2.1.13. Active Schedule Daily Repeating Schedule Report Command
    • 2.2.2. Alarm Command Class, version 1
      • 2.2.2.1. Interoperability considerations
      • 2.2.2.2. Alarm Get Command
      • 2.2.2.3. Alarm Report Command
    • 2.2.3. Alarm Command Class, version 2
      • 2.2.3.1. Interoperability considerations
      • 2.2.3.2. Alarm Set Command
      • 2.2.3.3. Alarm Get Command
      • 2.2.3.4. Alarm Report Command
      • 2.2.3.5. Alarm Type Supported Get Command
      • 2.2.3.6. Alarm Type Supported Report Command
    • 2.2.4. Alarm Sensor Command Class, version 1
      • 2.2.4.1. Alarm Sensor Get Command
      • 2.2.4.2. Alarm Sensor Report Command
      • 2.2.4.3. Alarm Sensor Supported Get Command
      • 2.2.4.4. Alarm Sensor Supported Report Command
    • 2.2.5. Alarm Silence Command Class, version 1
      • 2.2.5.1. Alarm Silence Set Command
    • 2.2.6. All Switch Command Class, version 1
      • 2.2.6.1. All Switch Set Command
      • 2.2.6.2. All Switch Get Command
      • 2.2.6.3. All Switch Report Command
      • 2.2.6.4. All Switch On Command
      • 2.2.6.5. All Switch Off Command
    • 2.2.7. Anti-theft Command Class, version 1
    • 2.2.8. Anti-theft Command Class, version 2
      • 2.2.8.1. Anti-theft Set Command
      • 2.2.8.2. Anti-theft Get Command
      • 2.2.8.3. Anti-theft Report Command
      • 2.2.8.4. Examples
        • 2.2.8.4.1. Example of a non-secure Thermostat
        • 2.2.8.4.2. Example of a security enabled Thermostat
    • 2.2.9. Anti-theft Command Class, version 3
      • 2.2.9.1. Compatibility Considerations
        • 2.2.9.1.1. Command Class dependencies
        • 2.2.9.1.2. Lock/Unlock requirements
        • 2.2.9.1.3. Multi Channel Considerations
      • 2.2.9.2. Anti-Theft Set Command
      • 2.2.9.3. Anti-theft Get Command
      • 2.2.9.4. Anti-Theft Report Command
    • 2.2.10. Anti-theft Unlock Command Class, version 1
      • 2.2.10.1. Compatibility Considerations
        • 2.2.10.1.1. Multi Channel Considerations
      • 2.2.10.2. Anti-Theft Unlock State Get Command
      • 2.2.10.3. Anti-Theft Unlock State Report Command
      • 2.2.10.4. Anti-Theft Unlock Set Command
    • 2.2.11. Authentication Command Class, version 1
      • 2.2.11.1. Terminology
      • 2.2.11.2. Interoperability Considerations
      • 2.2.11.3. Authentication Capability Get Command
      • 2.2.11.4. Authentication Capability Report Command
      • 2.2.11.5. Authentication Data Set Command
      • 2.2.11.6. Authentication Data Get Command
      • 2.2.11.7. Authentication Data Report Command
      • 2.2.11.8. Authentication Technologies Combination Set Command
      • 2.2.11.9. Authentication Technologies Combination Get Command
      • 2.2.11.10. Authentication Technologies Combination Report Command
      • 2.2.11.11. Authentication Checksum Get Command
      • 2.2.11.12. Authentication Checksum Report Command
      • 2.2.11.13. Examples and use-cases
    • 2.2.12. Authentication Media Write Command Class, version 1
      • 2.2.12.1. Authentication Media Capability Get Command
      • 2.2.12.2. Authentication Media Capability Report Command
      • 2.2.12.3. Authentication Media Write Start Command
      • 2.2.12.4. Authentication Media Write Stop Command
      • 2.2.12.5. Authentication Media Write Status Command
    • 2.2.13. Barrier Operator Command Class, version 1
      • 2.2.13.1. Compatibility considerations
        • 2.2.13.1.1. Node Information Frame (NIF)
        • 2.2.13.1.2. Command Class dependencies
      • 2.2.13.2. Barrier Operator Set Command
        • 2.2.13.2.1. Error Handling
      • 2.2.13.3. Barrier Operator Get Command
      • 2.2.13.4. Barrier Operator Report Command
      • 2.2.13.5. Barrier Operator Get Signaling Capabilities Supported Command
      • 2.2.13.6. Barrier Operator Report Signaling Capabilities Supported Command
      • 2.2.13.7. Barrier Operator Event Signal Set Command
      • 2.2.13.8. Barrier Operator Event Signaling Get Command
      • 2.2.13.9. Barrier Operator Event Signaling Report Command
    • 2.2.14. Basic Command Class, version 1
      • 2.2.14.1. Compatibility considerations
        • 2.2.14.1.1. Node Information Frame (NIF)
      • 2.2.14.2. Basic Set Command
      • 2.2.14.3. Basic Get Command
      • 2.2.14.4. Basic Report Command
    • 2.2.15. Basic Command Class, version 2
      • 2.2.15.1. Compatibility considerations
      • 2.2.15.2. Basic Report Command
    • 2.2.16. Basic Tariff Information Command Class, version 1
      • 2.2.16.1. Basic Tariff Information Get Command
      • 2.2.16.2. Basic Tariff Information Report Command
    • 2.2.17. Basic Window Covering Command Class, version 1
      • 2.2.17.1. Basic Window Covering Start Level Change Command
      • 2.2.17.2. Basic Window Covering Stop Level Change Command
    • 2.2.18. Binary Sensor Command Class, version 1
      • 2.2.18.1. Binary Sensor Get Command
      • 2.2.18.2. Binary Sensor Report Command
    • 2.2.19. Binary Sensor Command Class, version 2
      • 2.2.19.1. Binary Sensor Get Command
      • 2.2.19.2. Binary Sensor Report Command
      • 2.2.19.3. Binary Sensor Get Supported Sensor Command
      • 2.2.19.4. Binary Sensor Supported Sensor Report Command
    • 2.2.20. Binary Switch Command Class, version 1
      • 2.2.20.1. Binary Switch Set Command
      • 2.2.20.2. Binary Switch Get Command
      • 2.2.20.3. Binary Switch Report Command
    • 2.2.21. Binary Switch Command Class, version 2
      • 2.2.21.1. Compatibility considerations
      • 2.2.21.2. Binary Switch Set Command
      • 2.2.21.3. Binary Switch Report Command
    • 2.2.22. Binary Toggle Switch Command Class, version 1
      • 2.2.22.1. Binary Toggle Switch Set Command
      • 2.2.22.2. Binary Toggle Switch Get Command
      • 2.2.22.3. Binary Toggle Switch Report Command
    • 2.2.23. Central Scene Command Class, version 1
      • 2.2.23.1. Central Scene Supported Get Command
      • 2.2.23.2. Central Scene Supported Report Command
      • 2.2.23.3. Central Scene Notification Command
    • 2.2.24. Central Scene Command Class, version 2
      • 2.2.24.1. Compatibility considerations
      • 2.2.24.2. Central Scene Supported Report Command
      • 2.2.24.3. Central Scene Notification Command
    • 2.2.25. Central Scene Command Class, version 3
      • 2.2.25.1. Compatibility considerations
        • 2.2.25.1.1. Central Scene Configuration commands support
        • 2.2.25.1.2. Multi Channel considerations
      • 2.2.25.2. Central Scene Configuration Set Command
      • 2.2.25.3. Central Scene Configuration Get Command
      • 2.2.25.4. Central Scene Configuration Report Command
      • 2.2.25.5. Central Scene Supported Get Command
      • 2.2.25.6. Central Scene Supported Report Command
      • 2.2.25.7. Central Scene Notification Command
    • 2.2.26. Climate Control Schedule Command Class, version 1
      • 2.2.26.1. Schedule Set Command
      • 2.2.26.2. Schedule Get Command
      • 2.2.26.3. Schedule Report Command
      • 2.2.26.4. Schedule Changed Get Command
      • 2.2.26.5. Schedule Changed Report Command
      • 2.2.26.6. Schedule Override Set Command
      • 2.2.26.7. Schedule Override Get Command
      • 2.2.26.8. Schedule Override Report Command
    • 2.2.27. Clock Command Class, version 1
      • 2.2.27.1. Interoperability considerations
      • 2.2.27.2. Multi Channel Considerations
      • 2.2.27.3. Clock Set Command
      • 2.2.27.4. Clock Get Command
      • 2.2.27.5. Clock Report Command
    • 2.2.28. Color Switch Command Class, version 1
      • 2.2.28.1. Compatibility considerations
        • 2.2.28.1.1. Command Class dependencies
      • 2.2.28.2. Interoperability considerations
      • 2.2.28.3. Color Switch Supported Get Command
      • 2.2.28.4. Color Switch Supported Report Command
      • 2.2.28.5. Color Switch Get Command
      • 2.2.28.6. Color Switch Report Command
      • 2.2.28.7. Color Switch Set Command
      • 2.2.28.8. Color Switch Start Level Change Command
      • 2.2.28.9. Color Switch Stop Level Change Command
    • 2.2.29. Color Switch Command Class, version 2
      • 2.2.29.1. Compatibility considerations
        • 2.2.29.1.1. Command Class dependencies
      • 2.2.29.2. Interoperability considerations
      • 2.2.29.3. Color Switch Set Command
    • 2.2.30. Color Switch Command Class, version 3
      • 2.2.30.1. Compatibility considerations
        • 2.2.30.1.1. Command Class dependencies
      • 2.2.30.2. Interoperability considerations
      • 2.2.30.3. Color Switch Report Command
      • 2.2.30.4. Color Switch Start Level Change Command
    • 2.2.31. Configuration Command Class, version 1
      • 2.2.31.1. Compatibility considerations
        • 2.2.31.1.1. “Default” flag
      • 2.2.31.2. Configuration Set Command
      • 2.2.31.3. Configuration Get Command
      • 2.2.31.4. Configuration Report Command
    • 2.2.32. Configuration Command Class, version 2
      • 2.2.32.1. Compatibility considerations
        • 2.2.32.1.1. “Default” flag
      • 2.2.32.2. Interoperability considerations
      • 2.2.32.3. Configuration Set Command
      • 2.2.32.4. Configuration Bulk Set Command
      • 2.2.32.5. Configuration Bulk Get Command
      • 2.2.32.6. Configuration Bulk Report Command
    • 2.2.33. Configuration Command Class, version 3
      • 2.2.33.1. Compatibility considerations
        • 2.2.33.1.1. “Default” flag
        • 2.2.33.1.2. Configuration Properties Report
      • 2.2.33.2. Interoperability considerations
      • 2.2.33.3. Configuration Name Get Command
      • 2.2.33.4. Configuration Name Report Command
      • 2.2.33.5. Configuration Info Get Command
      • 2.2.33.6. Configuration Info Report Command
      • 2.2.33.7. Configuration Properties Get Command
      • 2.2.33.8. Configuration Properties Report Command
    • 2.2.34. Configuration Command Class, version 4
      • 2.2.34.1. Compatibility considerations
        • 2.2.34.1.1. Multi Channel Consideration
        • 2.2.34.1.2. “Default” flag
        • 2.2.34.1.3. Configuration Properties Report
        • 2.2.34.1.4. “Altering capabilities” flag
        • 2.2.34.1.5. “Advanced” flag
        • 2.2.34.1.6. Parameters value and network inclusion/exclusion
        • 2.2.34.1.7. Bulk commands support
      • 2.2.34.2. Configuration Set Command
      • 2.2.34.3. Configuration Bulk Set Command
      • 2.2.34.4. Configuration Properties Report Command
      • 2.2.34.5. Configuration Default Reset Command
    • 2.2.35. Controller Replication Command Class, version 1
      • 2.2.35.1. Transfer group command
      • 2.2.35.2. Transfer Group Name Command
      • 2.2.35.3. Transfer scene command
      • 2.2.35.4. Transfer Scene Name Command
    • 2.2.36. Demand Control Plan Configuration Command Class, version 1
      • 2.2.36.1. DCP list supported get command
      • 2.2.36.2. DCP list supported report command
      • 2.2.36.3. DCP list set command
      • 2.2.36.4. DCP list remove
    • 2.2.37. Demand Control Plan Monitor Command Class, version 1
      • 2.2.37.1. DCP list get command
      • 2.2.37.2. DCP list report command
      • 2.2.37.3. DCP event status get
      • 2.2.37.4. DCP event status report
    • 2.2.38. Door Lock Command Class, version 1-2
      • 2.2.38.1. Compatibility considerations
      • 2.2.38.2. Door Lock Operation Set Command
      • 2.2.38.3. Door Lock Operation Get Command
      • 2.2.38.4. Door Lock Operation Report Command
      • 2.2.38.5. Door Lock Configuration Set Command
      • 2.2.38.6. Door Lock Configuration Get Command
      • 2.2.38.7. Door Lock Configuration Report Command
    • 2.2.39. Door Lock Command Class, version 3
      • 2.2.39.1. Compatibility considerations
      • 2.2.39.2. Door Lock Operation Report Command
    • 2.2.40. Door Lock Command Class, version 4
      • 2.2.40.1. Terminology
      • 2.2.40.2. Compatibility considerations
      • 2.2.40.3. Door Lock Operation Set Command
      • 2.2.40.4. Door Lock Operation Get Command
      • 2.2.40.5. Door Lock Operation Report Command
      • 2.2.40.6. Door Lock Configuration Set Command
      • 2.2.40.7. Door Lock Configuration Get Command
      • 2.2.40.8. Door Lock Configuration Report Command
      • 2.2.40.9. Door Lock Capabilities Get Command
      • 2.2.40.10. Door Lock Capabilities Report Command
    • 2.2.41. Door Lock Logging Command Class, version 1
      • 2.2.41.1. Door Lock Logging Records Supported Get Command
      • 2.2.41.2. Door Lock Logging Records Supported Report Command
      • 2.2.41.3. Door Lock Logging Record Get Command
      • 2.2.41.4. Door Lock Logging Record Report Command
    • 2.2.42. Energy Production Command Class, version 1
      • 2.2.42.1. Energy Production Get Command
      • 2.2.42.2. Energy Production Report Command
    • 2.2.43. Entry Control Command Class, version 1
      • 2.2.43.1. Interoperability Considerations
      • 2.2.43.2. Security Considerations
      • 2.2.43.3. Handling user supplied data
      • 2.2.43.4. Handling Incorrect Entry
      • 2.2.43.5. Entry Control Notification Command
      • 2.2.43.6. Entry Control Key Supported Get Command
      • 2.2.43.7. Entry Control Key Supported Report Command
      • 2.2.43.8. Entry Control Event Supported Get Command
      • 2.2.43.9. Entry Control Event Supported Report Command
      • 2.2.43.10. Entry Control Configuration Set Command
      • 2.2.43.11. Entry Control Configuration Get Command
      • 2.2.43.12. Entry Control Configuration Report Command
      • 2.2.43.13. Event Types
    • 2.2.44. Generic Schedule Command Class, version 1
      • 2.2.44.1. Terminology
      • 2.2.44.2. Interoperability considerations
      • 2.2.44.3. Generic Schedule Capabilities Get Command
      • 2.2.44.4. Generic Schedule Capabilities Report Command
      • 2.2.44.5. Generic Schedule Time Range Set Command
        • 2.2.44.5.1. Time Range parameters and rules
      • 2.2.44.6. Generic Schedule Time Range Get Command
      • 2.2.44.7. Generic Schedule Time Range Report Command
      • 2.2.44.8. Generic Schedule Set Command
        • 2.2.44.8.1. Schedules and Time Ranges examples
      • 2.2.44.9. Generic Schedule Get Command
      • 2.2.44.10. Generic Schedule Report Command
    • 2.2.45. Geographic Location Command Class, version 1
      • 2.2.45.1. Multi Channel Considerations
      • 2.2.45.2. Geographic Location Set Command
      • 2.2.45.3. Geographic Location Get Command
      • 2.2.45.4. Geographic Location Report Command
    • 2.2.46. Geographic Location Command Class, version 2
      • 2.2.46.1. Z-Wave Geographic Location Command Class V2 obsoletes V1
      • 2.2.46.2. Multi Channel Considerations
      • 2.2.46.3. Geographic Location V2 Features
      • 2.2.46.4. Geographic Location V2 Examples
      • 2.2.46.5. Geographic Location Set Command
      • 2.2.46.6. Geographic Location Get Command
      • 2.2.46.7. Geographic Location Report Command
    • 2.2.47. HRV Status Command Class, version 1
      • 2.2.47.1. HRV Status Get Command
      • 2.2.47.2. HRV Status Report Command
      • 2.2.47.3. HRV Status Supported Get Command
      • 2.2.47.4. HRV Status Supported Report Command
    • 2.2.48. HRV Control Command Class, version 1
      • 2.2.48.1. HRV Mode Set Command
      • 2.2.48.2. HRV Mode Get Command
      • 2.2.48.3. HRV Mode Report Command
      • 2.2.48.4. HRV Bypass Set Command
      • 2.2.48.5. HRV Bypass Get Command
      • 2.2.48.6. HRV Bypass Report Command
      • 2.2.48.7. HRV Ventilation Rate Set Command
      • 2.2.48.8. HRV Ventilation Rate Get Command
      • 2.2.48.9. HRV Ventilation Rate Report Command
      • 2.2.48.10. HRV Mode Supported Get Command
      • 2.2.48.11. HRV Mode Supported Report Command
    • 2.2.49. Humidity Control Mode Command Class, version 1-2
      • 2.2.49.1. Humidity Control Mode Set Command
      • 2.2.49.2. Humidity Control Mode Get Command
      • 2.2.49.3. Humidity Control Mode Report Command
      • 2.2.49.4. Humidity Control Mode Supported Get Command
      • 2.2.49.5. Humidity Control Mode Supported Report Command
    • 2.2.50. Humidity Control Operating State Command Class, version 1
      • 2.2.50.1. Humidity Control Operating State Get Command
      • 2.2.50.2. Humidity Control Operating State Report Command
    • 2.2.51. Humidity Control Setpoint Command Class, version 1-2
      • 2.2.51.1. Humidity Control Setpoint Set Command
      • 2.2.51.2. Humidity Control Setpoint Get Command
      • 2.2.51.3. Humidity Control Setpoint Report Command
      • 2.2.51.4. Humidity Control Setpoint Supported Get Command
      • 2.2.51.5. Humidity Control Setpoint Supported Report Command
      • 2.2.51.6. Humidity Control Setpoint Scale Supported Get Command
      • 2.2.51.7. Humidity Control Setpoint Scale Supported Report Command
      • 2.2.51.8. Humidity Control Setpoint Capabilities Get Command
      • 2.2.51.9. Humidity Control Setpoint Capabilities Report Command
    • 2.2.52. IR Repeater Command Class, version 1
      • 2.2.52.1. IR Repeater Capabilities Get Command
      • 2.2.52.2. IR Repeater Capabilities Report Command
      • 2.2.52.3. IR Repeater IR Code Learning Start Command
      • 2.2.52.4. IR Repeater IR Code Learning Stop Command
      • 2.2.52.5. IR Repeater IR Code Learning Status Command
      • 2.2.52.6. IR Repeater Learnt IR Code Remove Command
      • 2.2.52.7. IR Repeater Learnt IR Code Get Command
      • 2.2.52.8. IR Repeater Learnt IR Code Report Command
      • 2.2.52.9. IR Repeater Learnt IR Code Readback Get Command
      • 2.2.52.10. IR Repeater Learnt IR Code Readback Report Command
      • 2.2.52.11. IR Repeater Configuration Set Command
      • 2.2.52.12. IR Repeater Configuration Get Command
      • 2.2.52.13. IR Repeater Configuration Report Command
      • 2.2.52.14. IR Repeater Repeat Learnt Code Command
      • 2.2.52.15. IR Repeater Repeat Command
    • 2.2.53. Irrigation Command Class, version 1
      • 2.2.53.1. Terminology
      • 2.2.53.2. Compatibility considerations
        • 2.2.53.2.1. Multi Channel considerations
      • 2.2.53.3. Interoperability considerations
        • 2.2.53.3.1. Controlling methods
      • 2.2.53.4. Irrigation System Info Get Command
      • 2.2.53.5. Irrigation System Info Report Command
      • 2.2.53.6. Irrigation System Status Get Command
      • 2.2.53.7. Irrigation System Status Report Command
      • 2.2.53.8. Irrigation System Config Set Command
      • 2.2.53.9. Irrigation System Config Get Command
      • 2.2.53.10. Irrigation System Config Report Command
      • 2.2.53.11. Irrigation Valve Info Get Command
      • 2.2.53.12. Irrigation Valve Info Report Command
      • 2.2.53.13. Irrigation Valve Config Set Command
      • 2.2.53.14. Irrigation Valve Config Get Command
      • 2.2.53.15. Irrigation Valve Config Report Command
      • 2.2.53.16. Irrigation Valve Run Command
      • 2.2.53.17. Irrigation Valve Table Set Command
      • 2.2.53.18. Irrigation Valve Table Get Command
      • 2.2.53.19. Irrigation Valve Table Report Command
      • 2.2.53.20. Irrigation Valve Table Run Command
      • 2.2.53.21. Irrigation System Shutoff Command
    • 2.2.54. Language Command Class, version 1
      • 2.2.54.1. Language Set Command
      • 2.2.54.2. Language Get Command
      • 2.2.54.3. Language Report Command
    • 2.2.55. Lock Command Class, version 1
      • 2.2.55.1. Lock Set Command
      • 2.2.55.2. Lock Get Command
      • 2.2.55.3. Lock Report Command
    • 2.2.56. Manufacturer Proprietary Command Class, version 1
      • 2.2.56.1. Manufacturer Proprietary Command
    • 2.2.57. Meter Command Class, version 1
      • 2.2.57.1. Terminology
      • 2.2.57.2. Meter Get Command
      • 2.2.57.3. Meter Report Command
    • 2.2.58. Meter Command Class, version 2
      • 2.2.58.1. Compatibility Considerations
      • 2.2.58.2. Meter Supported Get Command
      • 2.2.58.3. Meter Supported Report Command
      • 2.2.58.4. Meter Reset Command
      • 2.2.58.5. Meter Get Command
      • 2.2.58.6. Meter Report Command
    • 2.2.59. Meter Command Class, version 3
      • 2.2.59.1. Compatibility Considerations
      • 2.2.59.2. Meter Supported Report Command
      • 2.2.59.3. Meter Get Command
      • 2.2.59.4. Meter Report command
    • 2.2.60. Meter Command Class, version 4
      • 2.2.60.1. Compatibility Considerations
      • 2.2.60.2. Meter Supported Report Command
      • 2.2.60.3. Meter Get Command
      • 2.2.60.4. Meter Report Command
    • 2.2.61. Meter Command Class, version 5
      • 2.2.61.1. Compatibility considerations
      • 2.2.61.2. Meter Supported Report Command
      • 2.2.61.3. Meter Report Command
    • 2.2.62. Meter Command Class, version 6
      • 2.2.62.1. Compatibility Considerations
      • 2.2.62.2. Meter Reset Command
    • 2.2.63. Meter Table Configuration Command Class, version 1
      • 2.2.63.1. Meter Table Point Adm Number Set Command
    • 2.2.64. Meter Table Monitor Command Class, version 1
      • 2.2.64.1. Meter Table Point Adm. Number Get Command
      • 2.2.64.2. Meter Table Point Adm. Number Report Command
      • 2.2.64.3. Meter Table ID Get Command
      • 2.2.64.4. Meter Table ID Report Command
      • 2.2.64.5. Meter Table Capability Get Command
      • 2.2.64.6. Meter Table Capability Report Command
      • 2.2.64.7. Meter Table Status Supported Get Command
      • 2.2.64.8. Meter Table Status Supported Report Command
      • 2.2.64.9. Meter Table Status Depth Get Command
      • 2.2.64.10. Meter Table Status Date Get Command
      • 2.2.64.11. Meter Table Status Report Command
      • 2.2.64.12. Meter Table Current Data Get Command
      • 2.2.64.13. Meter Table Current Data Report Command
      • 2.2.64.14. Meter Table Historical Data Get Command
      • 2.2.64.15. Meter Table Historical Data Report Command
    • 2.2.65. Meter Table Monitor Command Class, version 2
      • 2.2.65.1. Compatibility Considerations
      • 2.2.65.2. Meter Table Point Adm. Number Report Command
      • 2.2.65.3. Meter Table ID Report Command
      • 2.2.65.4. Meter Table Capability Report Command
      • 2.2.65.5. Meter Table Current Data Report Command
      • 2.2.65.6. Meter Table Historical Data Report Command
    • 2.2.66. Meter Table Monitor Command Class, version 3
      • 2.2.66.1. Compatibility Considerations
    • 2.2.67. Meter Table Push Configuration Command Class, version 1
      • 2.2.67.1. Meter Table Push Configuration Set Command
      • 2.2.67.2. Meter Table Push Configuration Get Command
      • 2.2.67.3. Meter Table Push Configuration Report Command
    • 2.2.68. Move To Position Window Covering Command Class, version 1
      • 2.2.68.1. Move To Position Set Command
      • 2.2.68.2. Move To Position Get Command
      • 2.2.68.3. Move To Position Report Command
    • 2.2.69. Multilevel Sensor Command Class, version 1-4
      • 2.2.69.1. Multilevel Sensor Get Command
      • 2.2.69.2. Multilevel Sensor Report Command
    • 2.2.70. Multilevel Sensor Command Class, version 5-11
      • 2.2.70.1. Compatibility considerations
        • 2.2.70.1.1. Unknown Multilevel Sensor Types and Scales
      • 2.2.70.2. Multilevel Sensor Get Supported Sensor Command
      • 2.2.70.3. Multilevel Sensor Supported Sensor Report Command
      • 2.2.70.4. Multilevel Sensor Get Supported Scale Command
      • 2.2.70.5. Multilevel Sensor Supported Scale Report Command
      • 2.2.70.6. Multilevel Sensor Get Command
      • 2.2.70.7. Multilevel Sensor Report Command
        • 2.2.70.7.1. Detailed description: Sensor Types for Movement and Rotation
        • 2.2.70.7.2. Detailed description: Smoke Density
        • 2.2.70.7.3. Detailed description: RF Signal Strength
    • 2.2.71. Multilevel Switch Command Class, version 1
      • 2.2.71.1. Multilevel Switch Set Command
      • 2.2.71.2. Multilevel Switch Get Command
      • 2.2.71.3. Multilevel Switch Report Command
      • 2.2.71.4. Multilevel Switch Start Level Change Command
      • 2.2.71.5. Multilevel Switch Stop Level Change Command
    • 2.2.72. Multilevel Switch Command Class, version 2
      • 2.2.72.1. Compatibility considerations
      • 2.2.72.2. Multilevel Switch Set Command
      • 2.2.72.3. Multilevel Switch Start Level Change Command
    • 2.2.73. Multilevel Switch Command Class, version 3
      • 2.2.73.1. Compatibility considerations
      • 2.2.73.2. Multilevel Switch Supported Get Command
      • 2.2.73.3. Multilevel Switch Supported Report Command
      • 2.2.73.4. Multilevel Switch Start Level Change Command
    • 2.2.74. Multilevel Switch Command Class, version 4
      • 2.2.74.1. Compatibility considerations
      • 2.2.74.2. Multilevel Switch Report Command
    • 2.2.75. Multilevel Toggle Switch Command Class, version 1
      • 2.2.75.1. Multilevel Toggle Switch Set Command
      • 2.2.75.2. Multilevel Toggle Switch Get Command
      • 2.2.75.3. Multilevel Toggle Switch Report Command
      • 2.2.75.4. Multilevel Toggle Switch Start Level Change Command
      • 2.2.75.5. Multilevel Toggle Switch Stop Level Change Command
    • 2.2.76. Notification Command Class, version 3-8
      • 2.2.76.1. Terminology
      • 2.2.76.2. Compatibility considerations
        • 2.2.76.2.1. Notifications and Command Class version
        • 2.2.76.2.2. Push mode requirements
        • 2.2.76.2.3. Pull mode requirements
        • 2.2.76.2.4. Multi Channel considerations
      • 2.2.76.3. Interoperability considerations
        • 2.2.76.3.1. Push nodes Basic control
        • 2.2.76.3.2. Event flood
      • 2.2.76.4. Notification Set Command
      • 2.2.76.5. Notification Get Command
      • 2.2.76.6. Notification Report Command
        • 2.2.76.6.1. Event / State parameter encapsulation
      • 2.2.76.7. Notification Supported Get Command
      • 2.2.76.8. Notification Supported Report Command
      • 2.2.76.9. Event Supported Get Command
      • 2.2.76.10. Event Supported Report Command
    • 2.2.77. Prepayment Command Class, version 1
      • 2.2.77.1. Prepayment Balance Get Command
      • 2.2.77.2. Prepayment Balance Report Command
      • 2.2.77.3. Prepayment Supported Get Command
      • 2.2.77.4. Prepayment Supported Report Command
    • 2.2.78. Prepayment Encapsulation Command Class, version 1
      • 2.2.78.1. Prepayment encapsulation command
    • 2.2.79. Proprietary Command Class, version 1
      • 2.2.79.1. Proprietary set command
      • 2.2.79.2. Proprietary get command
      • 2.2.79.3. Proprietary report command
    • 2.2.80. Protection Command CLass, version 1
      • 2.2.80.1. Protection Set Command
      • 2.2.80.2. Protection get command
      • 2.2.80.3. Protection report command
    • 2.2.81. Protection Command Class, version 2
      • 2.2.81.1. Protection set command
      • 2.2.81.2. Protection report command
      • 2.2.81.3. Protection supported get command
      • 2.2.81.4. Protection supported report command
      • 2.2.81.5. Protection exclusive control
        • 2.2.81.5.1. Protection exclusive control set command
        • 2.2.81.5.2. Protection exclusive control get command
        • 2.2.81.5.3. Protection exclusive control report command
      • 2.2.81.6. Protection timeout
        • 2.2.81.6.1. Protection timeout set command
        • 2.2.81.6.2. Protection timeout get command
        • 2.2.81.6.3. Protection timeout report command
    • 2.2.82. Pulse Meter Command Class, version 1
      • 2.2.82.1. Pulse meter get command
      • 2.2.82.2. Pulse meter report command
    • 2.2.83. Rate Table Configuration Command Class, version 1
      • 2.2.83.1. Rate table set command
      • 2.2.83.2. Rate table remove command
    • 2.2.84. Rate Table Monitor Command Class, version 1
      • 2.2.84.1. Rate table supported get command
      • 2.2.84.2. Rate table supported report command
      • 2.2.84.3. Rate table get command
      • 2.2.84.4. Rate table report command
      • 2.2.84.5. Rate table active rate get command
      • 2.2.84.6. Rate table active rate report command
      • 2.2.84.7. Rate table current data get command
      • 2.2.84.8. Rate table current data report command
      • 2.2.84.9. Rate table historical data get command
      • 2.2.84.10. Rate table historical data report command
    • 2.2.85. Scene Activation Command Class, version 1
      • 2.2.85.1. Compatibility Considerations
      • 2.2.85.2. Scene Activation Set Command
    • 2.2.86. Scene Actuator Configuration Command Class, version 1
      • 2.2.86.1. Compatibility Considerations
      • 2.2.86.2. Scene Actuator Configuration Set Command
      • 2.2.86.3. Scene Actuator Configuration Get Command
      • 2.2.86.4. Scene Actuator Configuration Report Command
    • 2.2.87. Scene Controller Configuration Command Class, version 1
      • 2.2.87.1. Compatibility Considerations
      • 2.2.87.2. Scene Controller Configuration Set Command
      • 2.2.87.3. Scene Controller Configuration Get Command
      • 2.2.87.4. Scene Controller Configuration Report Command
    • 2.2.88. Schedule Command Class, version 1
      • 2.2.88.1. Terminology
      • 2.2.88.2. Interoperability Considerations
        • 2.2.88.2.1. Override Schedule
        • 2.2.88.2.2. Fall Back Schedule
        • 2.2.88.2.3. Multi Channel considerations
      • 2.2.88.3. Schedule Supported Get Command
      • 2.2.88.4. Schedule Supported Report Command
      • 2.2.88.5. Start Time Option: Start Now
      • 2.2.88.6. Start Time Option: Hour and Minute
      • 2.2.88.7. Start Time Option: Calendar Time
      • 2.2.88.8. Start Time Option: Weekday
      • 2.2.88.9. Schedule Set Command
        • 2.2.88.9.1. Start Time fields
        • 2.2.88.9.2. Duration fields
        • 2.2.88.9.3. Command and other fields
      • 2.2.88.10. Schedule Get Command
      • 2.2.88.11. Schedule Report Command
      • 2.2.88.12. Schedule Remove Command
      • 2.2.88.13. Schedule State Set Command
      • 2.2.88.14. Schedule State Get Command
      • 2.2.88.15. Schedule State Report Command
    • 2.2.89. Schedule Command Class, version 2
      • 2.2.89.1. Compatibility Considerations
        • 2.2.89.1.1. Schedule ID Blocks
        • 2.2.89.1.2. Schedule Command Class with Security
      • 2.2.89.2. Schedule Supported Get Command
      • 2.2.89.3. Schedule Supported Report Command
      • 2.2.89.4. Schedule Set Command
      • 2.2.89.5. Schedule Get Command
      • 2.2.89.6. Schedule Report Command
      • 2.2.89.7. Schedule Remove Command
      • 2.2.89.8. Schedule State Set Command
      • 2.2.89.9. Schedule State Get Command
      • 2.2.89.10. Schedule State Report Command
    • 2.2.90. Schedule Command Class, version 3
      • 2.2.90.1. Terminology
      • 2.2.90.2. Compatibility Considerations
      • 2.2.90.3. Schedule Supported Report Command
        • 2.2.90.3.1. Start Time Option: Start from now
        • 2.2.90.3.2. Start Time Mode: Recurring Mode
      • 2.2.90.4. Schedule Set Command
        • 2.2.90.4.1. Recurrence fields
        • 2.2.90.4.2. Start time fields
      • 2.2.90.5. Schedule Get Command
      • 2.2.90.6. Schedule Report Command
    • 2.2.91. Schedule Command Class, version 4
      • 2.2.91.1. Compatibility Considerations
      • 2.2.91.2. Schedule Supported Report Command
      • 2.2.91.3. Schedule Supported Commands Get Command
      • 2.2.91.4. Schedule Supported Commands Report Command
      • 2.2.91.5. Schedule Set Command
      • 2.2.91.6. Schedule Report Command
      • 2.2.91.7. Schedule State Report Command
    • 2.2.92. Schedule Entry Lock Command Class, version 1
      • 2.2.92.1. Schedule Entry Lock Enable Set Command
      • 2.2.92.2. Schedule Entry Lock Enable All Set Command
      • 2.2.92.3. Schedule Entry Lock Supported Get Command
      • 2.2.92.4. Schedule Entry Lock Supported Report Command
      • 2.2.92.5. Schedule Entry Lock Week Day Schedule Set Command
      • 2.2.92.6. Schedule Entry Lock Week Days Schedule Get Command
      • 2.2.92.7. Schedule Entry Lock Week Day Schedule Report Command
      • 2.2.92.8. Schedule Entry Lock Year Day Schedule Set Command
      • 2.2.92.9. Schedule Entry Lock Year Day Schedule Get Command
      • 2.2.92.10. Schedule Entry Lock Year Day Schedule Report Command
    • 2.2.93. Schedule Entry Lock Command Class, version 2
      • 2.2.93.1. Schedule Entry Lock Time Offset Get Command
      • 2.2.93.2. Schedule Entry Lock Time Offset Set Command
      • 2.2.93.3. Schedule Entry Lock Time Offset Report Command
    • 2.2.94. Schedule Entry Lock Command Class, version 3
      • 2.2.94.1. Schedule Entry Type Supported Report Command
      • 2.2.94.2. Schedule Entry Lock Daily Repeating Set Command
      • 2.2.94.3. Schedule Entry Lock Daily Repeating Get Command
      • 2.2.94.4. Schedule Entry Lock Daily Repeating Report Command
    • 2.2.95. Schedule Entry Lock Command Class, version 4
      • 2.2.95.1. Extended Schedule Entry Lock Enable Set Command
      • 2.2.95.2. Extended Schedule Entry Lock Week Day Schedule Set Command
      • 2.2.95.3. Extended Schedule Entry Lock Week Day Schedule Get Command
      • 2.2.95.4. Extended Schedule Entry Lock Week Day Schedule Report Command
      • 2.2.95.5. Extended Schedule Entry Lock Year Day Schedule Set Command
      • 2.2.95.6. Extended Schedule Entry Lock Year Day Schedule Get Command
      • 2.2.95.7. Extended Schedule Entry Lock Year Day Schedule Report Command
      • 2.2.95.8. Extended Schedule Entry Lock Daily Repeating Set Command
      • 2.2.95.9. Extended Schedule Entry Lock Daily Repeating Get Command
      • 2.2.95.10. Extended Schedule Entry Lock Daily Repeating Report Command
    • 2.2.96. Screen Attributes Command Class, version 1
      • 2.2.96.1. Screen Attributes Get Command
      • 2.2.96.2. Screen Attributes Report Command
    • 2.2.97. Screen Attributes Command Class, version 2
      • 2.2.97.1. Screen Attributes Report Command
    • 2.2.98. Screen Meta Data Command Class, version 1
      • 2.2.98.1. Screen Meta Data Get Command
      • 2.2.98.2. Screen Meta Data Report Command
    • 2.2.99. Screen Meta Data Command Class, version 2
      • 2.2.99.1. Screen Meta Data Report Command
    • 2.2.100. Sensor Configuration Command Class, version 1
      • 2.2.100.1. Sensor Trigger Level Set Command
      • 2.2.100.2. Sensor Trigger Level Get Command
      • 2.2.100.3. Sensor Trigger Level Report Command
      • 2.2.100.4. Mapping Example
    • 2.2.101. Simple AV Control Command Class, version 1-4
      • 2.2.101.1. Simple AV Control Set Command
      • 2.2.101.2. Simple AV Control Get Command
      • 2.2.101.3. Simple AV Control Report Command
      • 2.2.101.4. Simple AV Control Supported Get Command
      • 2.2.101.5. Simple AV Control Supported Report Command
    • 2.2.102. Sound Switch Command Class, version 1
      • 2.2.102.1. Terminology
      • 2.2.102.2. Compatibility Considerations
      • 2.2.102.3. Sound Switch Tones Number Get Command
      • 2.2.102.4. Sound Switch Tones Number Report Command
      • 2.2.102.5. Sound Switch Tone Info Get Command
      • 2.2.102.6. Sound Switch Tone Info Report Command
      • 2.2.102.7. Sound Switch Configuration Set Command
      • 2.2.102.8. Sound Switch Configuration Get Command
      • 2.2.102.9. Sound Switch Configuration Report Command
      • 2.2.102.10. Sound Switch Tone Play Set Command
      • 2.2.102.11. Sound Switch Tone Play Get Command
      • 2.2.102.12. Sound Switch Tone Play Report Command
    • 2.2.103. Sound Switch Command Class, version 2
      • 2.2.103.1. Compatibility Considerations
      • 2.2.103.2. Sound Switch Tone Play Set Command
      • 2.2.103.3. Sound Switch Tone Play Report Command
    • 2.2.104. Tariff Table Configuration Command Class, version 1
      • 2.2.104.1. Tariff Table Supplier Set Command
      • 2.2.104.2. Tariff Table Set Command
      • 2.2.104.3. Tariff Table Remove Command
    • 2.2.105. Tariff Table Monitor Command Class, version 1
      • 2.2.105.1. Tariff Table Supplier Get Command
      • 2.2.105.2. Tariff Table Supplier Report Command
      • 2.2.105.3. Tariff Table Get Command
      • 2.2.105.4. Tariff Table Report Command
      • 2.2.105.5. Tariff Table Cost Get Command
      • 2.2.105.6. Tariff Table Cost Report Command
    • 2.2.106. Thermostat Fan Mode Command Class, version 1
      • 2.2.106.1. Thermostat Fan Mode Set Command
      • 2.2.106.2. Thermostat Fan Mode Get Command
      • 2.2.106.3. Thermostat Fan Mode Report Command
      • 2.2.106.4. Thermostat Fan Mode Supported Get Command
      • 2.2.106.5. Thermostat Fan Mode Supported Report Command
    • 2.2.107. Thermostat Fan Mode Command Class, version 2
      • 2.2.107.1. Thermostat Fan Mode Set Command
      • 2.2.107.2. Thermostat Fan Mode Report Command
    • 2.2.108. Thermostat Fan Mode Command Class, version 3
      • 2.2.108.1. Thermostat Fan Mode Set Command
      • 2.2.108.2. Thermostat Fan Mode Get Command
      • 2.2.108.3. Thermostat Fan Mode Report Command
    • 2.2.109. Thermostat Fan Mode Command Class, version 4-5
      • 2.2.109.1. Thermostat Fan Mode Set Command
      • 2.2.109.2. Thermostat Fan Mode Get Command
      • 2.2.109.3. Thermostat Fan Mode Report Command
      • 2.2.109.4. Thermostat Fan Mode Supported Get Command
      • 2.2.109.5. Thermostat Fan Mode Supported Report Command
    • 2.2.110. Thermostat Fan State Command Class, version 1-2
      • 2.2.110.1. Compatibility Considerations
      • 2.2.110.2. Thermostat Fan State Get Command
      • 2.2.110.3. Thermostat Fan State Report Command
    • 2.2.111. Thermostat Mode Command Class, version 1-2
      • 2.2.111.1. Interoperability Considerations
      • 2.2.111.2. Thermostat Mode Set Command
      • 2.2.111.3. Thermostat Mode Get Command
      • 2.2.111.4. Thermostat Mode Report Command
      • 2.2.111.5. Thermostat Mode Supported Get Command
      • 2.2.111.6. Thermostat Mode Supported Report Command
    • 2.2.112. Thermostat Mode Command Class, version 3
      • 2.2.112.1. Compatibility Considerations
      • 2.2.112.2. Interoperability Considerations
      • 2.2.112.3. Thermostat Mode Set Command
      • 2.2.112.4. Thermostat Mode Report Command
    • 2.2.113. Thermostat Operating State Command Class, version 1
      • 2.2.113.1. Thermostat Operating State Get Command
      • 2.2.113.2. Thermostat Operating State Report Command
    • 2.2.114. Thermostat Operating State Command Class, version 2
      • 2.2.114.1. Thermostat Operating State Get
      • 2.2.114.2. Thermostat Operating State Report
      • 2.2.114.3. Thermostat Operating State Logging Supported Get
      • 2.2.114.4. Thermostat Operating State Logging Supported Report
      • 2.2.114.5. Thermostat Operating State Logging Get
      • 2.2.114.6. Thermostat Operating State Logging Report
    • 2.2.115. Thermostat Setback Command Class, version 1
      • 2.2.115.1. Thermostat Setback Set Command
      • 2.2.115.2. Thermostat Setback Get Command
      • 2.2.115.3. Thermostat Setback Report Command
    • 2.2.116. Thermostat Setpoint Command Class, version 1-2
      • 2.2.116.1. Interoperability Considerations
        • 2.2.116.1.1. Setpoint Type Bitmask Interpretation
        • 2.2.116.1.2. Float Encoding
      • 2.2.116.2. Thermostat Setpoint Set Command
      • 2.2.116.3. Thermostat Setpoint Get Command
      • 2.2.116.4. Thermostat Setpoint Report Command
      • 2.2.116.5. Thermostat Setpoint Supported Get Command
      • 2.2.116.6. Thermostat Setpoint Supported Report Command
    • 2.2.117. Thermostat Setpoint Command Class, version 3
      • 2.2.117.1. Compatibility Considerations
      • 2.2.117.2. Interoperability Considerations
        • 2.2.117.2.1. Setpoint Type Bitmask Interpretation
        • 2.2.117.2.2. Float Encoding
      • 2.2.117.3. Thermostat Setpoint Set Command
      • 2.2.117.4. Thermostat Setpoint Get Command
      • 2.2.117.5. Thermostat Setpoint Report Command
      • 2.2.117.6. Thermostat Setpoint Supported Get Command
      • 2.2.117.7. Thermostat Setpoint Supported Report Command
      • 2.2.117.8. Thermostat Setpoint Capabilities Get Command
      • 2.2.117.9. Thermostat Setpoint Capabilities Report Command
    • 2.2.118. User Code Command Class, version 1
      • 2.2.118.1. Interoperability Considerations
      • 2.2.118.2. User Code Set Command
      • 2.2.118.3. User Code Get Command
      • 2.2.118.4. User Code Report Command
      • 2.2.118.5. Users Number Get Command
      • 2.2.118.6. Users Number Report Command
    • 2.2.119. User Code Command Class, version 2
      • 2.2.119.1. Terminology
      • 2.2.119.2. Compatibility Considerations
      • 2.2.119.3. Interoperability Considerations
        • 2.2.119.3.1. User Management
      • 2.2.119.4. Security Considerations
      • 2.2.119.5. User Code Set Command
      • 2.2.119.6. Users Number Report Command
      • 2.2.119.7. User Code Capabilities Get Command
      • 2.2.119.8. User Code Capabilities Report Command
      • 2.2.119.9. User Code Keypad Mode Set Command
      • 2.2.119.10. User Code Keypad Mode Get Command
      • 2.2.119.11. User Code Keypad Mode Report Command
      • 2.2.119.12. Extended User Code Set Command
      • 2.2.119.13. Extended User Code Get Command
      • 2.2.119.14. Extended User Code Report Command
      • 2.2.119.15. Admin Code Set Command
      • 2.2.119.16. Admin Code Get Command
      • 2.2.119.17. Admin Code Report Command
      • 2.2.119.18. User Code Checksum Get Command
      • 2.2.119.19. User Code Checksum Report Command
    • 2.2.120. User Credential Command Class, version 1
      • 2.2.120.1. Terminology
      • 2.2.120.2. Compatibility Considerations
        • 2.2.120.2.1. User Code Command Class Dependencies
        • 2.2.120.2.2. Schedule Entry Lock Command Class Dependencies
        • 2.2.120.2.3. Notification Command Class Dependencies
        • 2.2.120.2.4. Door Lock Command Class Dependencies
      • 2.2.120.3. Security Considerations
      • 2.2.120.4. User Capabilities Get Command
      • 2.2.120.5. User Capabilities Report Command
      • 2.2.120.6. Credential Capabilities Get Command
      • 2.2.120.7. Credential Capabilities Report Command
      • 2.2.120.8. User Set Command
      • 2.2.120.9. User Get Command
      • 2.2.120.10. User Report Command
      • 2.2.120.11. Credential Set Command
      • 2.2.120.12. Credential Get Command
      • 2.2.120.13. Credential Report Command
      • 2.2.120.14. Credential Learn Start Command
      • 2.2.120.15. Credential Learn Cancel Command
      • 2.2.120.16. Credential Learn Status Report Command
      • 2.2.120.17. User Credential Association Set Command
      • 2.2.120.18. User Credential Association Report Command
      • 2.2.120.19. All Users Checksum Get Command
      • 2.2.120.20. All Users Checksum Report Command
      • 2.2.120.21. User Checksum Get Command
      • 2.2.120.22. User Checksum Report Command
      • 2.2.120.23. Credential Checksum Get Command
      • 2.2.120.24. Credential Checksum Report Command
      • 2.2.120.25. Admin Code Information
      • 2.2.120.26. Admin PIN Code Set Command
      • 2.2.120.27. Admin PIN Code Get Command
      • 2.2.120.28. Admin PIN Code Report Command
    • 2.2.121. User Credential Command Class, version 2
      • 2.2.121.1. Terminology
        • 2.2.121.1.1. Key Locker
        • 2.2.121.1.2. User Management
      • 2.2.121.2. Compatibility Considerations
        • 2.2.121.2.1. Active Schedule Command Class Dependencies
        • 2.2.121.2.2. Application Status Command Class Dependencies
        • 2.2.121.2.3. User Code Command Class Dependencies
      • 2.2.121.3. User Capabilities Report Command
      • 2.2.121.4. Credential Set Command
        • 2.2.121.4.1. MIFARE DESFire Credential Type Requirements
      • 2.2.121.5. Key Locker Capabilities Get Command
      • 2.2.121.6. Key Locker Capabilities Report Command
      • 2.2.121.7. Key Locker Entry Set Command
      • 2.2.121.8. Key Locker Entry Get Command
      • 2.2.121.9. Key Locker Entry Report Command
    • 2.2.122. Window Covering Command Class, version 1
      • 2.2.122.1. Terminology
      • 2.2.122.2. Compatibility Considerations
        • 2.2.122.2.1. Motor Control Device Class Support
        • 2.2.122.2.2. Command Class Dependencies
      • 2.2.122.3. Window Covering Parameters
      • 2.2.122.4. Window Covering Supported Get Command
      • 2.2.122.5. Window Covering Supported Report Command
      • 2.2.122.6. Window Covering Get Command
      • 2.2.122.7. Window Covering Report Command
      • 2.2.122.8. Window Covering Set Command
      • 2.2.122.9. Window Covering Start Level Change Command
      • 2.2.122.10. Window Covering Stop Level Change Command
• 3. Management Command Classes
  • 3.1. Management Command Class Overview
  • 3.2. Management Command Class Definitions
    • 3.2.1. Application Capability Command Class, version 1
      • 3.2.1.1. Not Supported Command Class Command
    • 3.2.2. Application Status Command Class, version 1
      • 3.2.2.1. Compatibility Considerations
        • 3.2.2.1.1. Node Information Frame (NIF)
      • 3.2.2.2. Application Busy Command
      • 3.2.2.3. Application Rejected Request Command
    • 3.2.3. Association Command Class, version 1
      • 3.2.3.1. Compatibility Considerations
      • 3.2.3.2. Z-Wave Plus Considerations
      • 3.2.3.3. Security Considerations
      • 3.2.3.4. Association Set Command
      • 3.2.3.5. Association Get Command
      • 3.2.3.6. Association Report Command
      • 3.2.3.7. Association Remove Command
      • 3.2.3.8. Association Supported Groupings Get Command
      • 3.2.3.9. Association Supported Groupings Report Command
    • 3.2.4. Association Command Class, version 2
      • 3.2.4.1. Compatibility Considerations
      • 3.2.4.2. Z-Wave Plus Considerations
      • 3.2.4.3. Security Considerations
      • 3.2.4.4. Association Remove Command
      • 3.2.4.5. Association Specific Group Get Command
      • 3.2.4.6. Association Specific Group Report Command
    • 3.2.5. Association Command Class, version 3
      • 3.2.5.1. Compatibility Considerations
      • 3.2.5.2. Interoperability Considerations
    • 3.2.6. Association Command Class, version 4
      • 3.2.6.1. Compatibility Considerations
      • 3.2.6.2. Interoperability Considerations
    • 3.2.7. Association Command Configuration Command Class, version 1
      • 3.2.7.1. Command Records Supported Get Command
      • 3.2.7.2. Command Records Supported Report Command
      • 3.2.7.3. Command Configuration Set Command
      • 3.2.7.4. Command Configuration Get Command
      • 3.2.7.5. Command Configuration Report Command
    • 3.2.8. Association Group Information (AGI) Command Class, version 1
      • 3.2.8.1. Compatibility considerations
        • 3.2.8.1.1. Multi Channel considerations
      • 3.2.8.2. Association Principles
      • 3.2.8.3. The Association Group Information
        • 3.2.8.3.1. Group identifier
        • 3.2.8.3.2. Profile
        • 3.2.8.3.3. Command Class and Command
        • 3.2.8.3.4. Association group name
      • 3.2.8.4. Association Group Name Get
      • 3.2.8.5. Association Group Name Report
      • 3.2.8.6. Association Group Info Get
      • 3.2.8.7. Association Group Info Report
      • 3.2.8.8. Association Group Command List Get
      • 3.2.8.9. Association Group Command List Report
    • 3.2.9. Association Group Information (AGI) Command Class, version 2
      • 3.2.9.1. Compatibility considerations
      • 3.2.9.2. The Association Group Information
        • 3.2.9.2.1. Profile
    • 3.2.10. Association Group Information (AGI) Command Class, version 3
      • 3.2.10.1. Compatibility considerations
      • 3.2.10.2. The Association Group Information
        • 3.2.10.2.1. Profile
    • 3.2.11. Battery Command Class, version 1
      • 3.2.11.1. Battery Get Command
      • 3.2.11.2. Battery Report Command
    • 3.2.12. Battery Command Class, version 2
      • 3.2.12.1. Compatibility Considerations
      • 3.2.12.2. Battery Get Command
      • 3.2.12.3. Battery Report Command
      • 3.2.12.4. Battery Health Get Command
      • 3.2.12.5. Battery Health Report Command
    • 3.2.13. Battery Command Class, version 3
      • 3.2.13.1. Battery Report Command
    • 3.2.14. Device Reset Locally Command Class, version 1
      • 3.2.14.1. Device Reset Locally Notification Command
    • 3.2.15. Firmware Update Meta Data Command Class, version 1
      • 3.2.15.1. Firmware Meta Data Get Command
      • 3.2.15.2. Firmware Meta Data Report Command
      • 3.2.15.3. Firmware Update Meta Data Request Get Command
      • 3.2.15.4. Firmware Update Meta Data Request Report Command
      • 3.2.15.5. Firmware Update Meta Data Get Command
      • 3.2.15.6. Firmware Update Meta Data Report Command
      • 3.2.15.7. Firmware Update Meta Data Status Report Command
      • 3.2.15.8. Examples
    • 3.2.16. Firmware Update Meta Data Command Class, version 2
      • 3.2.16.1. Compatibility considerations
      • 3.2.16.2. Interoperability considerations
        • 3.2.16.2.1. Interoperability with v1 devices
        • 3.2.16.2.2. Checksum calculation
      • 3.2.16.3. Firmware Update Meta Data Report Command
    • 3.2.17. Firmware Update Meta Data Command Class, version 3
      • 3.2.17.1. Compatibility considerations
        • 3.2.17.1.1. New fields and values
      • 3.2.17.2. Interoperability considerations
        • 3.2.17.2.1. Interoperability with v1 devices
        • 3.2.17.2.2. Checksum calculation
      • 3.2.17.3. Firmware Meta Data Report Command
      • 3.2.17.4. Firmware Update Meta Data Request Get Command
      • 3.2.17.5. Firmware Update Meta Data Request Report Command
      • 3.2.17.6. Firmware Update Meta Data Get Command
      • 3.2.17.7. Firmware Update Meta Data Report Command
      • 3.2.17.8. Firmware Update Meta Data Status Report Command
    • 3.2.18. Firmware Update Meta Data Command Class, version 4
      • 3.2.18.1. Compatibility considerations
        • 3.2.18.1.1. New commands, fields and values
      • 3.2.18.2. Interoperability considerations
        • 3.2.18.2.1. Interoperability with v1 devices
        • 3.2.18.2.2. Checksum calculation
      • 3.2.18.3. Firmware Update Meta Data Request Get Command
      • 3.2.18.4. Firmware Update Meta Data Status Report Command
      • 3.2.18.5. Firmware Update Activation Set Command
      • 3.2.18.6. Firmware Update Activation Status Report
    • 3.2.19. Firmware Update Meta Data Command Class, version 5
      • 3.2.19.1. Compatibility considerations
        • 3.2.19.1.1. New commands, fields and values
      • 3.2.19.2. Interoperability Considerations
        • 3.2.19.2.1. Interoperability with v1 devices
        • 3.2.19.2.2. Checksum calculation
      • 3.2.19.3. Firmware Meta Data Report Command
      • 3.2.19.4. Firmware Update Meta Data Request Get Command
      • 3.2.19.5. Firmware Update Meta Data Request Report Command
      • 3.2.19.6. Firmware Update Meta Data Status Report Command
      • 3.2.19.7. Firmware Update Activation Set Command
      • 3.2.19.8. Firmware Update Activation Status Report Command
      • 3.2.19.9. Firmware Update Meta Data Prepare Get Command
      • 3.2.19.10. Firmware Update Meta Data Prepare Report Command
      • 3.2.19.11. Examples
        • 3.2.19.11.1. Identifying firmware revisions
        • 3.2.19.11.2. Firmware download
    • 3.2.20. Firmware Update Meta Data Command Class, version 6
      • 3.2.20.1. Compatibility considerations
      • 3.2.20.2. Firmware Meta Data Report Command
      • 3.2.20.3. Firmware Update Meta Data Request Report Command
    • 3.2.21. Firmware Update Meta Data Command Class, version 7
      • 3.2.21.1. Compatibility considerations
      • 3.2.21.2. Firmware Meta Data Report Command
      • 3.2.21.3. Firmware Update Meta Data Request Get Command
    • 3.2.22. Firmware Update Meta Data Command Class, version 8
      • 3.2.22.1. Compatibility Considerations
      • 3.2.22.2. Interoperability Considerations
        • 3.2.22.2.1. Interoperability with v1 devices
        • 3.2.22.2.2. Checksum calculation
        • 3.2.22.2.3. Firmware Activation
      • 3.2.22.3. Firmware Data fields
        • 3.2.22.3.1. Manufacturer ID (16 bits)
        • 3.2.22.3.2. Firmware ID (16 bits)
        • 3.2.22.3.3. Firmware Checksum (16 bits)
        • 3.2.22.3.4. Firmware target (8 bits)
        • 3.2.22.3.5. Hardware Version (8 bits)
      • 3.2.22.4. Firmware Meta Data Get Command
      • 3.2.22.5. Firmware Meta Data Report Command
      • 3.2.22.6. Firmware Update Meta Data Request Get Command
      • 3.2.22.7. Firmware Update Meta Data Request Report Command
      • 3.2.22.8. Firmware Update Meta Data Get Command
      • 3.2.22.9. Firmware Update Meta Data Report Command
      • 3.2.22.10. Firmware Update Meta Data Status Report Command
      • 3.2.22.11. Firmware Update Activation Set Command
      • 3.2.22.12. Firmware Update Activation Status Report Command
      • 3.2.22.13. Firmware Update Meta Data Prepare Get Command
      • 3.2.22.14. Firmware Update Meta Data Prepare Report Command
      • 3.2.22.15. Firmware Update Examples and frame flows
        • 3.2.22.15.1. Requesting Firmware information
        • 3.2.22.15.2. Performing a Firmware update
        • 3.2.22.15.3. Identifying Firmware revisions
        • 3.2.22.15.4. Firmware Activation
        • 3.2.22.15.5. Firmware download
        • 3.2.22.15.6. Firmware Resume
        • 3.2.22.15.7. Non-secure Firmware update
        • 3.2.22.15.8. Rejecting firmware updates or downloads
    • 3.2.23. Grouping Name Command Class, version 1
      • 3.2.23.1. Grouping Name Set Command
      • 3.2.23.2. Grouping Name Get Command
      • 3.2.23.3. Group Name Report Command
    • 3.2.24. Hail Command Class, version 1
      • 3.2.24.1. Hail Command
    • 3.2.25. Indicator Command Class, version 1
      • 3.2.25.1. Interoperability considerations
      • 3.2.25.2. Indicator Set Command
      • 3.2.25.3. Indicator Get Command
      • 3.2.25.4. Indicator Report Command
    • 3.2.26. Indicator Command Class, version 2
      • 3.2.26.1. Compatibility Considerations
      • 3.2.26.2. Interoperability considerations
      • 3.2.26.3. Indicator Set Command
      • 3.2.26.4. Indicator Get Command
      • 3.2.26.5. Indicator Report Command
      • 3.2.26.6. Indicator Supported Get Command
      • 3.2.26.7. Indicator Supported Report Command
    • 3.2.27. Indicator Command Class, version 3
      • 3.2.27.1. Compatibility Considerations
    • 3.2.28. Indicator Command Class, version 4
      • 3.2.28.1. Compatibility Considerations
      • 3.2.28.2. Indicator Description Get Command
      • 3.2.28.3. Indicator Description Report Command
    • 3.2.29. IP Association Command Class, version 1
      • 3.2.29.1. Compatibility considerations
      • 3.2.29.2. Terminology
      • 3.2.29.3. Z-Wave Multi Channel compatibility considerations
      • 3.2.29.4. Advertising the IP Association Command Class
      • 3.2.29.5. IP Association Set Command
      • 3.2.29.6. IP Association Get Command
      • 3.2.29.7. IP Association Report Command
      • 3.2.29.8. IP Association Remove Command
    • 3.2.30. Manufacturer Specific Command Class, version 1
      • 3.2.30.1. Security Considerations
      • 3.2.30.2. Manufacturer Specific Get Command
      • 3.2.30.3. Manufacturer Specific Report Command
    • 3.2.31. Manufacturer Specific Command Class, version 2
      • 3.2.31.1. Security Considerations
      • 3.2.31.2. Device Specific Get Command
      • 3.2.31.3. Device Specific Report Command
    • 3.2.32. Multi Instance Association Command Class, version 1
    • 3.2.33. Multi Channel Association Command Class, version 2
      • 3.2.33.1. Compatibility Considerations
      • 3.2.33.2. Z-Wave Plus Considerations
      • 3.2.33.3. Security Considerations
      • 3.2.33.4. Multi Channel Association Set Command
      • 3.2.33.5. Multi Channel Association Get Command
      • 3.2.33.6. Multi Channel Association Report Command
      • 3.2.33.7. Multi Channel Association Remove Command
        • 3.2.33.7.1. Examples
      • 3.2.33.8. Multi Channel Association Supported Groupings Get Command
      • 3.2.33.9. Multi Channel Association Supported Groupings Report Command
    • 3.2.34. Multi Channel Association Command Class, version 3
      • 3.2.34.1. Compatibility Considerations
      • 3.2.34.2. Z-Wave Plus Considerations
      • 3.2.34.3. Security Considerations
      • 3.2.34.4. Multi Channel Association Set Command
    • 3.2.35. Multi Channel Association Command Class, version 4
      • 3.2.35.1. Compatibility Considerations
      • 3.2.35.2. Interoperability Considerations
    • 3.2.36. Multi Channel Association Command Class, version 5
      • 3.2.36.1. Compatibility Considerations
      • 3.2.36.2. Interoperability Considerations
    • 3.2.37. Node Naming and Location Command Class, version 1
      • 3.2.37.1. Node Name Set Command
      • 3.2.37.2. Node Name Get Command
      • 3.2.37.3. Node Name Report Command
      • 3.2.37.4. Node Location Set Command
      • 3.2.37.5. Node Location Get Command
      • 3.2.37.6. Node Location Report Command
    • 3.2.38. Remote Association Activation Command Class, version 1
      • 3.2.38.1. Remote Association Activate Command
    • 3.2.39. Remote Association Configuration Command Class, version 1
      • 3.2.39.1. Remote Association Configuration Set Command
      • 3.2.39.2. Remote Association Configuration Get Command
      • 3.2.39.3. Remote Association Configuration Report Command
    • 3.2.40. Time Command Class, version 1
      • 3.2.40.1. Compatibility considerations
        • 3.2.40.1.1. Node Information Frame (NIF)
      • 3.2.40.2. Interoperability considerations
      • 3.2.40.3. Time Get Command
      • 3.2.40.4. Time Report Command
      • 3.2.40.5. Date Get Command
      • 3.2.40.6. Date Report Command
    • 3.2.41. Time Command Class, version 2
      • 3.2.41.1. Compatibility considerations
        • 3.2.41.1.1. Node Information Frame (NIF)
      • 3.2.41.2. Interoperability considerations
      • 3.2.41.3. Time Offset Get Command
      • 3.2.41.4. Time Offset Set Command
      • 3.2.41.5. Time Offset Report Command
    • 3.2.42. Time Command Class, version 3
      • 3.2.42.1. Compatibility Considerations
        • 3.2.42.1.1. Node Information Frame (NIF)
      • 3.2.42.2. Interoperability Considerations
      • 3.2.42.3. Security Considerations
      • 3.2.42.4. Time Report Command
      • 3.2.42.5. Time Set Command
      • 3.2.42.6. Date Set Command
    • 3.2.43. Time Parameters Command Class, version 1
      • 3.2.43.1. Time Parameters Set Command
      • 3.2.43.2. Time Parameters Get Command
      • 3.2.43.3. Time Parameters Report Command
    • 3.2.44. Version Command Class, version 1
      • 3.2.44.1. Compatibility Considerations
      • 3.2.44.2. Security Considerations
      • 3.2.44.3. Version Get Command
      • 3.2.44.4. Version Report Command
      • 3.2.44.5. Version Command Class Get Command
      • 3.2.44.6. Version Command Class Report Command
    • 3.2.45. Version Command Class, version 2
      • 3.2.45.1. Version Report Command
    • 3.2.46. Version Command Class, version 3
      • 3.2.46.1. Compatibility considerations
      • 3.2.46.2. Version Capabilities Get Command
      • 3.2.46.3. Version Capabilities Report Command
      • 3.2.46.4. Version Z-Wave Software Get Command
      • 3.2.46.5. Version Z-Wave Software Report Command
        • 3.2.46.5.1. Version fields
    • 3.2.47. Version Command Class, version 4
      • 3.2.47.1. Compatibility Considerations
      • 3.2.47.2. Terminology
        • 3.2.47.2.1. Migration
        • 3.2.47.2.2. Operation
      • 3.2.47.3. Version Capabilities Report Command
      • 3.2.47.4. Version Migration Capabilities Get Command
      • 3.2.47.5. Version Migration Capabilities Report Command
      • 3.2.47.6. Version Migration Set Command
      • 3.2.47.7. Version Migration Get Command
      • 3.2.47.8. Version Migration Report Command
    • 3.2.48. Wake Up Command Class, version 1
      • 3.2.48.1. Terminology
      • 3.2.48.2. Interoperability considerations
      • 3.2.48.3. Wake Up Interval Set Command
      • 3.2.48.4. Wake Up Interval Get Command
      • 3.2.48.5. Wake Up Interval Report Command
      • 3.2.48.6. Wake Up Notification Command
      • 3.2.48.7. Wake Up No More Information Command
    • 3.2.49. Wake Up Command Class, version 2
      • 3.2.49.1. Compatibility considerations
      • 3.2.49.2. Wake Up Interval Set Command
      • 3.2.49.3. Wake Up Interval Capabilities Get Command
      • 3.2.49.4. Wake Up Interval Capabilities Report Command
    • 3.2.50. Wake Up Command Class, version 3
      • 3.2.50.1. Wake Up Interval Capabilities Report Command
        • 3.2.50.1.1. Wake Up On Demand functionality
    • 3.2.51. Z/IP Naming and Location Command Class, version 1
      • 3.2.51.1. Compatibility Considerations
      • 3.2.51.2. Z/IP Name Set Command
      • 3.2.51.3. Z/IP Name Get Command
      • 3.2.51.4. Z/IP Name Report Command
      • 3.2.51.5. Z/IP Location Set Command
      • 3.2.51.6. Z/IP Location Get Command
      • 3.2.51.7. Z/IP Location Report Command
    • 3.2.52. Z-Wave Plus Info Command Class, version 1
    • 3.2.53. Z-Wave Plus Info Command Class, version 2
      • 3.2.53.1. Compatibility Considerations
        • 3.2.53.1.1. Node Information Frame (NIF)
      • 3.2.53.2. Multi Channel considerations
      • 3.2.53.3. Z-Wave Plus Info Get Command
      • 3.2.53.4. Z-Wave Plus Info Report Command
• 4. Transport-Encapsulation Command Classes
  • 4.1. Transport-Encapsulation Command Class Overview
    • 4.1.1. Encapsulation Command Classes Support/Control
    • 4.1.2. Node Information Frame
    • 4.1.3. Multi Channel Overview
      • 4.1.3.1. Terminology
      • 4.1.3.2. Backwards compatibility
      • 4.1.3.3. GUI presentation
      • 4.1.3.4. Applicability examples
      • 4.1.3.5. Encapsulation order overview
  • 4.2. Transport-Encapsulation Command Class Definitions
    • 4.2.1. CRC-16 Encapsulation Command Class, version 1
      • 4.2.1.1. Compatibility Considerations
        • 4.2.1.1.1. Node Information Frame (NIF)
        • 4.2.1.1.2. Control and support
      • 4.2.1.2. CRC-16 Encapsulated Command
    • 4.2.2. Multi Channel Command Class, version 3
      • 4.2.2.1. Compatibility Considerations
        • 4.2.2.1.1. Node information Frame (NIF)
        • 4.2.2.1.2. Dynamic End Point considerations
      • 4.2.2.2. Interoperability considerations
      • 4.2.2.3. Multi Channel End Point Get Command
      • 4.2.2.4. Multi Channel End Point Report Command
      • 4.2.2.5. Multi Channel Capability Get Command
      • 4.2.2.6. Multi Channel Capability Report Command
      • 4.2.2.7. Multi Channel End Point Find Command
      • 4.2.2.8. Multi Channel End Point Find Report Command
      • 4.2.2.9. Multi Channel Command Encapsulation
    • 4.2.3. Multi Channel Command Class, version 4
      • 4.2.3.1. Compatibility Considerations
      • 4.2.3.2. Interoperability Considerations
        • 4.2.3.2.1. Aggregated End Point design principles
        • 4.2.3.2.2. Dynamic End Point considerations
      • 4.2.3.3. Multi Channel End Point Report Command
      • 4.2.3.4. Multi Channel Capability Get/Report Commands
      • 4.2.3.5. Multi Channel Capability Find Report Commands
      • 4.2.3.6. Multi Channel Aggregated Members Get Command
      • 4.2.3.7. Multi Channel Aggregated Members Report Command
    • 4.2.4. Multi Command Command Class, version 1
      • 4.2.4.1. Interoperability considerations
      • 4.2.4.2. Compatibility considerations
        • 4.2.4.2.1. Multi Command Support
        • 4.2.4.2.2. Multi Command Control
        • 4.2.4.2.3. Node Information Frame (NIF)
      • 4.2.4.3. Multi Command Encapsulated Command
    • 4.2.5. Security 0 (S0) Command Class, version 1
      • 4.2.5.1. Compatibility considerations
        • 4.2.5.1.1. Node Information Frame (NIF)
      • 4.2.5.2. Message Encapsulation and Command Class Handling
        • 4.2.5.2.1. Nonce Get Command
        • 4.2.5.2.2. Nonce Report Command
        • 4.2.5.2.3. Security Message Encapsulation Command
      • 4.2.5.3. Network Key Management
        • 4.2.5.3.1. Network inclusion
        • 4.2.5.3.2. Security Scheme Get Command
        • 4.2.5.3.3. Security Scheme Report Command
        • 4.2.5.3.4. Network Key Set Command
        • 4.2.5.3.5. Network Key Verify Command
        • 4.2.5.3.6. Security Scheme Inherit Command
      • 4.2.5.4. Encapsulated Command Class Handling
        • 4.2.5.4.1. Multi Channel Handling
        • 4.2.5.4.2. Security Commands Supported Get Command
        • 4.2.5.4.3. Security Commands Supported Report Command
    • 4.2.6. Security 2 (S2) Command Class, version 1
      • 4.2.6.1. Compatibility Considerations
        • 4.2.6.1.1. Command Class dependencies
        • 4.2.6.1.2. Node Information Frame (NIF)
        • 4.2.6.1.3. Mixed Security Classes
        • 4.2.6.1.4. Migration of existing devices to the Security 2 Command Class
      • 4.2.6.2. Security Considerations
        • 4.2.6.2.1. Application enabled delivery confirmation
        • 4.2.6.2.2. Potential Singlecast Delay Attack via interception and jamming
        • 4.2.6.2.3. Potential Multicast Delay Attack
        • 4.2.6.2.4. Circumventing DSK authentication
      • 4.2.6.3. Interoperability Considerations
        • 4.2.6.3.1. Pragmatic Decryption calculations in constrained environments
      • 4.2.6.4. Building Blocks
        • 4.2.6.4.1. ECDH Key pair generation
        • 4.2.6.4.2. Key exchange overview
        • 4.2.6.4.3. Core AES (AES)
        • 4.2.6.4.4. AES-128 CCM Encryption and Authentication
        • 4.2.6.4.5. CCM profile
        • 4.2.6.4.6. Message Authentication Code - AES-128 CMAC
        • 4.2.6.4.7. Pseudo Random Number Generator (PRNG)
        • 4.2.6.4.8. Key extraction and derivation
        • 4.2.6.4.9. Nonces for CCM
        • 4.2.6.4.10. SPAN NextNonce Generator
        • 4.2.6.4.11. MPAN NextNonce Generator
      • 4.2.6.5. Message Encapsulation
        • 4.2.6.5.1. Singlecast messages and SPAN Management
        • 4.2.6.5.2. Multicast messages and MPAN Management
        • 4.2.6.5.3. Message encapsulation commands
        • 4.2.6.5.4. Duplicate Message Detection
      • 4.2.6.6. Key Management
        • 4.2.6.6.1. Key Exchange
        • 4.2.6.6.2. ECDH key pairs, Device Specific Key and User Verification
        • 4.2.6.6.3. Client-Side Authentication
        • 4.2.6.6.4. Initial Key Exchange
      • 4.2.6.7. Security 2 Key Exchange commands
        • 4.2.6.7.1. Security 2 KEX Get Command
        • 4.2.6.7.2. Security 2 KEX Report Command
        • 4.2.6.7.3. Security 2 KEX Set Command
        • 4.2.6.7.4. Security 2 KEX Fail Command
        • 4.2.6.7.5. Security 2 Public Key Report Command
        • 4.2.6.7.6. Security 2 Network Key Get Command
        • 4.2.6.7.7. Security 2 Network Key Report Command
        • 4.2.6.7.8. Security 2 Network Key Verify Command
        • 4.2.6.7.9. Security 2 Transfer End Command
      • 4.2.6.8. Discovery of Security Capabilities Commands
        • 4.2.6.8.1. Security 2 Commands Supported Get Command
        • 4.2.6.8.2. Security 2 Commands Supported Report Command
    • 4.2.7. Security 2 (S2) Command Class, version 2
      • 4.2.7.1. Network Layer Security (NLS) Introduction
      • 4.2.7.2. Compatibility considerations
      • 4.2.7.3. Security considerations
      • 4.2.7.4. Interoperability considerations
      • 4.2.7.5. Commands covered by NLS
        • 4.2.7.5.1. Z-Wave Network Layer commands ALWAYS covered by NLS
        • 4.2.7.5.2. Z-Wave Network Layer commands covered by NLS after secure bootstrapping
        • 4.2.7.5.3. Z-Wave Network Layer commands NOT covered by NLS
        • 4.2.7.5.4. Z-Wave Network Layer commands NEVER covered by NLS
        • 4.2.7.5.5. Z-Wave Long Range Network Layer commands NOT covered by NLS
        • 4.2.7.5.6. Z-Wave Long Range Network Layer commands NEVER covered by NLS
      • 4.2.7.6. KEX Report Command
      • 4.2.7.7. NLS Node List Get Command
      • 4.2.7.8. NLS Node List Report Command
      • 4.2.7.9. NLS State Get Command
      • 4.2.7.10. NLS State Report Command
      • 4.2.7.11. NLS State Set Command
    • 4.2.8. Supervision Command Class, version 1
      • 4.2.8.1. Terminology
      • 4.2.8.2. Compatibility Considerations
        • 4.2.8.2.1. Node Information Frame (NIF)
        • 4.2.8.2.2. Encapsulated Commands
      • 4.2.8.3. Supervision Get Command
      • 4.2.8.4. Supervision Report Command
      • 4.2.8.5. Examples and use-cases
        • 4.2.8.5.1. Set Type commands
        • 4.2.8.5.2. Powerlevel Test Node Set Command
        • 4.2.8.5.3. Report/Notification Type Commands
        • 4.2.8.5.4. Remove Type commands
    • 4.2.9. Supervision Command Class, version 2
      • 4.2.9.1. Compatibility considerations
      • 4.2.9.2. Supervision Report Command
        • 4.2.9.2.1. Wake up on Demand functionality
    • 4.2.10. Transport Service Command Class, version 1
    • 4.2.11. Transport Service Command Class, version 2
      • 4.2.11.1. Compatibility considerations
        • 4.2.11.1.1. Node Information Frame (NIF)
      • 4.2.11.2. Example Frame flows
        • 4.2.11.2.1. As things should always work - the default case
        • 4.2.11.2.2. Losing first segment of a long message
        • 4.2.11.2.3. Losing subsequent segment
        • 4.2.11.2.4. Losing last segment
        • 4.2.11.2.5. Losing SegmentComplete
• 5. Network-Protocol Command Classes
  • 5.1. Network-Protocol Command Class Overview
  • 5.2. Network-Protocol Command Class Definitions
    • 5.2.1. Inclusion Controller Command Class, version 1
      • 5.2.1.1. Compatibility considerations
        • 5.2.1.1.1. Node information frame (NIF)
        • 5.2.1.1.2. Legacy controllers
      • 5.2.1.2. Inclusion controller initiate command
      • 5.2.1.3. Inclusion controller complete command
    • 5.2.2. IP Configuration Command Class, version 1
      • 5.2.2.1. IP configuration set command
      • 5.2.2.2. IP configuration get command
      • 5.2.2.3. IP configuration report command
      • 5.2.2.4. IP configuration DHCP release command
      • 5.2.2.5. IP configuration DHCP renew command
    • 5.2.3. Mailbox Command Class, version 1
      • 5.2.3.1. Mailbox framework
        • 5.2.3.1.1. Mailbox proxy
        • 5.2.3.1.2. Mailbox service
        • 5.2.3.1.3. Frame flow
      • 5.2.3.2. Mailbox configuration get command
      • 5.2.3.3. Mailbox configuration set command
      • 5.2.3.4. Mailbox configuration report command
      • 5.2.3.5. Mailbox queue command
      • 5.2.3.6. Mailbox wake up notification command
      • 5.2.3.7. Mailbox failing node command
      • 5.2.3.8. Frame flow diagrams Examples
    • 5.2.4. Mailbox Command Class, version 2
      • 5.2.4.1. Examples and frame flows
        • 5.2.4.1.1. Node interview process
    • 5.2.5. Network Management Command Classes
      • 5.2.5.1. Compatibility considerations
        • 5.2.5.1.1. Sequence number management
      • 5.2.5.2. Scope of network management
        • 5.2.5.2.1. Intranode
        • 5.2.5.2.2. Intranet (LAN)
        • 5.2.5.2.3. Internet (WAN)
      • 5.2.5.3. Security considerations
        • 5.2.5.3.1. Designing for single-threading and limited transmit buffer
      • 5.2.5.4. Network management proxy command class, version 1
        • 5.2.5.4.1. Node list get command
        • 5.2.5.4.2. Node list report command
        • 5.2.5.4.3. Node info cached get command
        • 5.2.5.4.4. Node info cached report command
      • 5.2.5.5. Network management proxy command class, version 2
        • 5.2.5.5.1. Compatibility considerations
        • 5.2.5.5.2. Node info cached report command
        • 5.2.5.5.3. Network management multi channel end point get command
        • 5.2.5.5.4. Network management multi channel end point report command
        • 5.2.5.5.5. Network management multi channel capability get command
        • 5.2.5.5.6. Network management multi channel capability report command
        • 5.2.5.5.7. Network management multi channel aggregated members get command
        • 5.2.5.5.8. Network management multi channel aggregated members report command
      • 5.2.5.6. Network management proxy command class, version 3
        • 5.2.5.6.1. Compatibility considerations
        • 5.2.5.6.2. Failed node list get command
        • 5.2.5.6.3. Failed node list report command
      • 5.2.5.7. Network management proxy command class, version 4
        • 5.2.5.7.1. Compatibility Considerations
        • 5.2.5.7.2. Node list report command
        • 5.2.5.7.3. Node info cached get command
        • 5.2.5.7.4. Network management multi channel end point get command
        • 5.2.5.7.5. Network management multi channel end point report command
        • 5.2.5.7.6. Network management multi channel capability get command
        • 5.2.5.7.7. Network management multi channel capability report command
        • 5.2.5.7.8. Network management multi channel aggregated members get command
        • 5.2.5.7.9. Network management multi channel aggregated members report command
        • 5.2.5.7.10. Failed node list report command
      • 5.2.5.8. Network Management Basic Node Command Class, version 1
        • 5.2.5.8.1. Default set command
        • 5.2.5.8.2. Default set complete command
        • 5.2.5.8.3. Learn mode set command
        • 5.2.5.8.4. Learn mode set status command
        • 5.2.5.8.5. Node information send command
        • 5.2.5.8.6. Network update request command
        • 5.2.5.8.7. Network update request status command
        • 5.2.5.8.8. Use cases and frame flows
      • 5.2.5.9. Network management basic node command class, version 2
        • 5.2.5.9.1. Compatibility considerations
        • 5.2.5.9.2. Learn mode set command
        • 5.2.5.9.3. Learn mode set status command
        • 5.2.5.9.4. DSK get command
        • 5.2.5.9.5. DSK Report Command
        • 5.2.5.9.6. Use cases and frame flows
      • 5.2.5.10. Network management inclusion command class, version 1
        • 5.2.5.10.1. Node add command
        • 5.2.5.10.2. Node add status command
        • 5.2.5.10.3. Node remove command
        • 5.2.5.10.4. Node remove status command
        • 5.2.5.10.5. Failed node remove command
        • 5.2.5.10.6. Node neighbor update request command
        • 5.2.5.10.7. Node neighbor update status command
        • 5.2.5.10.8. Return route assign command
        • 5.2.5.10.9. Return route assign complete command
        • 5.2.5.10.10. Return route delete command
        • 5.2.5.10.11. Return route delete complete command
        • 5.2.5.10.12. Use cases and frame flows
      • 5.2.5.11. Network management inclusion command class, version 2
        • 5.2.5.11.1. Compatibility considerations
        • 5.2.5.11.2. Node add command
        • 5.2.5.11.3. Node add status command
        • 5.2.5.11.4. Node add keys report command
        • 5.2.5.11.5. Node add DSK report command
        • 5.2.5.11.6. Node add DSK set command
        • 5.2.5.11.7. Failed node replace command
        • 5.2.5.11.8. Failed node replace status command
        • 5.2.5.11.9. Use cases and frame flows
      • 5.2.5.12. Network management inclusion command class, version 3
        • 5.2.5.12.1. Compatibility considerations
        • 5.2.5.12.2. Node add status command
        • 5.2.5.12.3. Included node information frame report command
        • 5.2.5.12.4. Smart start join started command
        • 5.2.5.12.5. Usage and frame flows
      • 5.2.5.13. Network management inclusion command class, version 4
        • 5.2.5.13.1. Compatibility considerations
        • 5.2.5.13.2. Failed node remove command
        • 5.2.5.13.3. Failed node remove status command
        • 5.2.5.13.4. Extended node add status command
        • 5.2.5.13.5. Usage and frame flows
      • 5.2.5.14. Network management primary command class, version 1 [OBSOLETED]
        • 5.2.5.14.1. Controller change command
        • 5.2.5.14.2. Controller change status command
      • 5.2.5.15. Network management installation and maintenance command class, version 1
        • 5.2.5.15.1. Priority route set
        • 5.2.5.15.2. Priority route get
        • 5.2.5.15.3. Priority route report
        • 5.2.5.15.4. Statistics get
        • 5.2.5.15.5. Statistics report
        • 5.2.5.15.6. Statistics clear
        • 5.2.5.15.7. Use cases
      • 5.2.5.16. Network management installation and maintenance command class, version 2
        • 5.2.5.16.1. Compatibility considerations
        • 5.2.5.16.2. RSSI get command
        • 5.2.5.16.3. RSSI report command
      • 5.2.5.17. Network management installation and maintenance command class, version 3
        • 5.2.5.17.1. Compatibility considerations
        • 5.2.5.17.2. S2 resynchronization event command
        • 5.2.5.17.3. Extended statistics get
        • 5.2.5.17.4. Extended statistics report
      • 5.2.5.18. Network management installation and maintenance command class, version 4
        • 5.2.5.18.1. Compatibility considerations
        • 5.2.5.18.2. RSSI report command
        • 5.2.5.18.3. Z-Wave long range channel configuration set
        • 5.2.5.18.4. Z-Wave long range channel configuration get
        • 5.2.5.18.5. Z-Wave long range channel configuration report
    • 5.2.6. No Operation Command Class, version 1
    • 5.2.7. Node Provisioning Command Class, version 1
      • 5.2.7.1. Terminology
      • 5.2.7.2. Compatibility considerations
      • 5.2.7.3. Security considerations
      • 5.2.7.4. Node Provisioning Set Command
      • 5.2.7.5. Node Provisioning Delete Command
      • 5.2.7.6. Node Provisioning Get Command
      • 5.2.7.7. Node Provisioning Report Command
      • 5.2.7.8. Node Provisioning List Iteration Get Command
      • 5.2.7.9. Node Provisioning List Iteration Report Command
      • 5.2.7.10. Meta Data Extension Format
      • 5.2.7.11. Usage and Frame Flows
        • 5.2.7.11.1. Z/IP Client requesting the entire Node Provisioning list.
    • 5.2.8. Powerlevel Command Class, version 1
      • 5.2.8.1. Powerlevel Set Command
      • 5.2.8.2. Powerlevel Get Command
      • 5.2.8.3. Powerlevel Report Command
      • 5.2.8.4. Powerlevel Test Node Set Command
      • 5.2.8.5. Powerlevel Test Node Get Command
      • 5.2.8.6. Powerlevel Test Node Report Command
    • 5.2.9. Z/IP Command Class, version 1
    • 5.2.10. Z/IP Command Class, version 2
      • 5.2.10.1. Security considerations
      • 5.2.10.2. Interoperability considerations
      • 5.2.10.3. Z/IP Packet Command
    • 5.2.11. Z/IP Command Class, version 3
      • 5.2.11.1. Compatibility considerations
      • 5.2.11.2. Z/IP Packet Command
    • 5.2.12. Z/IP Command Class, version 4
      • 5.2.12.1. Compatibility considerations
      • 5.2.12.2. Z/IP Keep Alive Command
    • 5.2.13. Z/IP Command Class, version 5
      • 5.2.13.1. Compatibility considerations
      • 5.2.13.2. List of defined Z/IP Packet Options
        • 5.2.13.2.1. Expected Delay Option
        • 5.2.13.2.2. Installation and Maintenance Get Option
        • 5.2.13.2.3. Installation and Maintenance Report Option
        • 5.2.13.2.4. Encapsulation Format Information Option
        • 5.2.13.2.5. Z-Wave Multicast Addressing Option
    • 5.2.14. Z/IP 6LoWPAN Command Class, version 1
    • 5.2.15. Z/IP Gateway Comand Class, version 1
      • 5.2.15.1. Interoperability considerations
      • 5.2.15.2. Gateway Mode Set Command
      • 5.2.15.3. Gateway Mode Get Command
      • 5.2.15.4. Gateway Mode Report Command
      • 5.2.15.5. Gateway Peer Set Command
      • 5.2.15.6. Gateway Peer Get Command
      • 5.2.15.7. Gateway Peer Report Command
      • 5.2.15.8. Gateway Lock Set Command
      • 5.2.15.9. Unsolicited Destination Set Command
      • 5.2.15.10. Unsolicited Destination Get Command
      • 5.2.15.11. Unsolicited Destination Report Command
      • 5.2.15.12. Application Node Info Set Command
      • 5.2.15.13. Application Node Info Get Command
      • 5.2.15.14. Application Node Info Report Command
    • 5.2.16. Z/IP ND Command Class, version 1
      • 5.2.16.1. Interoperability considerations
      • 5.2.16.2. Security considerations
      • 5.2.16.3. Z/IP Node Solicitation Command
      • 5.2.16.4. Z/IP Inverse Node Solicitation Command
      • 5.2.16.5. Z/IP Node Advertisement Command
    • 5.2.17. Z/IP ND Command Class, version 2
      • 5.2.17.1. Compatibility Considerations
      • 5.2.17.2. Interoperability considerations
      • 5.2.17.3. Security considerations
      • 5.2.17.4. Z/IP Inverse Node Solicitation Command
      • 5.2.17.5. Z/IP Node Advertisement Command
    • 5.2.18. Z/IP Portal Command Class, version 1
      • 5.2.18.1. Interoperability considerations
        • 5.2.18.1.1. On the use of Z/IP Gateway and Z/IP Portal command classes
      • 5.2.18.2. Gateway Configuration Set Command
      • 5.2.18.3. Gateway Configuration Status
      • 5.2.18.4. Gateway Configuration Get Command
      • 5.2.18.5. Gateway Configuration Report Command:
      • 5.2.18.6. Gateway Unregister Command
• 6. Command Class Control Specification
  • 6.1. Command Class Control Overview
    • 6.1.1. Controlled and Supported Command Classes
      • 6.1.1.1. Control via association groups
      • 6.1.1.2. “Full” control
      • 6.1.1.3. Partial Control
    • 6.1.2. Command Classes Support Discovery Requirements
    • 6.1.3. Command Classes Control Requirements
      • 6.1.3.1. Mandatory supporting node interview
      • 6.1.3.2. Minimum end user functionalities
      • 6.1.3.3. Command Class control version
    • 6.1.4. Command Classes not Present in this Document
  • 6.2. Application Command Classes
    • 6.2.1. Active Schedule Command Class, version 1
      • 6.2.1.1. Mandatory node interview
      • 6.2.1.2. Target Schedule Data Interview
      • 6.2.1.3. Minimum end user functionalities
        • 6.2.1.3.1. Attach, Modify or Delete a Schedule
        • 6.2.1.3.2. Query the State of a Schedule
        • 6.2.1.3.3. Enable or Disable Schedules for a Target
      • 6.2.1.4. Node properties
      • 6.2.1.5. Supported Target Command Classes
    • 6.2.2. Anti-theft Unlock Command Class, version 1
      • 6.2.2.1. Mandatory node interview
      • 6.2.2.2. Minimum end user functionalities
        • 6.2.2.2.1. Unlock the node
      • 6.2.2.3. Node properties
    • 6.2.3. Barrier Operator Command Class, version 1
      • 6.2.3.1. Mandatory node interview
      • 6.2.3.2. Minimum end user functionalities
        • 6.2.3.2.1. Initiate opening (or stop closing)
        • 6.2.3.2.2. Initiate closing
      • 6.2.3.3. Node properties
      • 6.2.3.4. Additional control requirements
    • 6.2.4. Basic Command Class, version 1-2
      • 6.2.4.1. Mandatory node interview
      • 6.2.4.2. Minimum end user functionalities
        • 6.2.4.2.1. Set the node On/Off state
      • 6.2.4.3. Node properties
      • 6.2.4.4. Additional control requirements
    • 6.2.5. Binary Switch Command Class, version 1-2
      • 6.2.5.1. Mandatory node interview
      • 6.2.5.2. Minimum end user functionalities
        • 6.2.5.2.1. Set the node On/Off state
      • 6.2.5.3. Node properties
    • 6.2.6. Central Scene Command Class, version 1-3
      • 6.2.6.1. Mandatory node interview
      • 6.2.6.2. Minimum end user functionalities
      • 6.2.6.3. Node properties
      • 6.2.6.4. Additional control requirements
    • 6.2.7. Color Switch Command Class, version 1-3
      • 6.2.7.1. Mandatory node interview
      • 6.2.7.2. Minimum end user functionalities
        • 6.2.7.2.1. Set the color
        • 6.2.7.2.2. Fade/enhance a color component
        • 6.2.7.2.3. Stop fading/enhancing a color component
      • 6.2.7.3. Node properties
      • 6.2.7.4. Additional control requirements
    • 6.2.8. Configuration Command Class, version 1-4
      • 6.2.8.1. Mandatory node interview
      • 6.2.8.2. Minimum end user functionalities
        • 6.2.8.2.1. Set a configuration parameter Value
        • 6.2.8.2.2. Reset all configuration parameter values to default
      • 6.2.8.3. Node properties
      • 6.2.8.4. Additional control requirements
    • 6.2.9. Door Lock Command Class, version 1-4
      • 6.2.9.1. Mandatory node interview
      • 6.2.9.2. Minimum end user functionalities
        • 6.2.9.2.1. Configure the door lock
        • 6.2.9.2.2. Set the door mode
      • 6.2.9.3. Node properties
    • 6.2.10. Entry Control Command Class, version 1
      • 6.2.10.1. Mandatory node interview
      • 6.2.10.2. Minimum end user functionalities
        • 6.2.10.2.1. Configure the keypad
      • 6.2.10.3. Node properties
      • 6.2.10.4. Additional control requirements
    • 6.2.11. IR Repeater Command Class, version 1
      • 6.2.11.1. Mandatory node interview
      • 6.2.11.2. Minimum end user functionalities
        • 6.2.11.2.1. Repeat an IR code
        • 6.2.11.2.2. Learn an IR code
        • 6.2.11.2.3. Erase a learnt IR code
        • 6.2.11.2.4. Repeat a learnt IR code
      • 6.2.11.3. Node properties
    • 6.2.12. Meter Command Class, version 1-5
      • 6.2.12.1. Mandatory node interview
      • 6.2.12.2. Minimum end user functionalities
        • 6.2.12.2.1. Reset cumulated data
      • 6.2.12.3. Node properties
      • 6.2.12.4. Additional control requirements
    • 6.2.13. Multilevel Sensor Command Class, version 1-11
      • 6.2.13.1. Mandatory node interview
      • 6.2.13.2. Minimum end user functionalities
      • 6.2.13.3. Node properties
      • 6.2.13.4. Additional control requirements
    • 6.2.14. Multilevel Switch Command Class, version 1-4
      • 6.2.14.1. Mandatory node interview
      • 6.2.14.2. Mimimum End User Functionalities
        • 6.2.14.2.1. Set the Level
      • 6.2.14.3. Node Properties
    • 6.2.15. Notification Command Class, version 1-8
      • 6.2.15.1. Mandatory Node Interview
      • 6.2.15.2. Minimum End User Functionalities
      • 6.2.15.3. Node Properties
      • 6.2.15.4. Additional Control Requirements
        • 6.2.15.4.1. Detailed Controller Guidelines
    • 6.2.16. Simple AV Control Command Class, version 1-4
      • 6.2.16.1. Mandatory Node interview
      • 6.2.16.2. Minimum end user functionalities
        • 6.2.16.2.1. Send a supported AV code
      • 6.2.16.3. Node properties
    • 6.2.17. Sound Switch Command Class, version 1
      • 6.2.17.1. Mandatory node interview
      • 6.2.17.2. Minimum end user functionalities
        • 6.2.17.2.1. Configure the sound switch
        • 6.2.17.2.2. Play/stop a selected or default tone
      • 6.2.17.3. Node properties
    • 6.2.18. Thermostat Mode Command Class, version 1-3
      • 6.2.18.1. Mandatory interview
      • 6.2.18.2. Minimum end user functionalities
        • 6.2.18.2.1. Change mode
      • 6.2.18.3. Node properties
    • 6.2.19. Thermostat Setback Command Class, version 1
      • 6.2.19.1. Mandatory interview
      • 6.2.19.2. Minimum end user functionalities
        • 6.2.19.2.1. Configure setback
      • 6.2.19.3. Node properties
    • 6.2.20. Thermostat Setpoint Command Class, version 1-3
      • 6.2.20.1. Mandatory interview
      • 6.2.20.2. Minimum end user functionalities
        • 6.2.20.2.1. Change setpoint for a supported type
      • 6.2.20.3. Node properties
    • 6.2.21. User Code Command Class, version 1-2
      • 6.2.21.1. Mandatory interview
      • 6.2.21.2. Minimum end user functionalities
        • 6.2.21.2.1. Set/modify a User Code
        • 6.2.21.2.2. Erase a User Code
        • 6.2.21.2.3. Set the keypad mode (v2)
        • 6.2.21.2.4. Set the Admin Code (v2)
      • 6.2.21.3. Node properties
      • 6.2.21.4. Additional control requirements
    • 6.2.22. User Credential Command Class, version 1-2
      • 6.2.22.1. User Management Overview
      • 6.2.22.2. Mandatory interview
      • 6.2.22.3. Minimum end user functionalities
        • 6.2.22.3.1. Add/Modify a User
        • 6.2.22.3.2. Delete a User
        • 6.2.22.3.3. Add/Modify a Credential
        • 6.2.22.3.4. Delete a Credential
        • 6.2.22.3.5. Set the Admin PIN Code
        • 6.2.22.3.6. Add/Modify a Key Locker Entry
        • 6.2.22.3.7. Delete a Key Locker Entry
      • 6.2.22.4. Node properties
      • 6.2.22.5. Additional control requirements
    • 6.2.23. Window Covering Command Class, version 1
      • 6.2.23.1. Mandatory interview
      • 6.2.23.2. Minimum end user functionalities
        • 6.2.23.2.1. Go to position
        • 6.2.23.2.2. Start level change up or down
        • 6.2.23.2.3. Stop level change
      • 6.2.23.3. Node properties
      • 6.2.23.4. Additional control requirements
  • 6.3. Management Command Classes
    • 6.3.1. Association Command Class, version 1-4
      • 6.3.1.1. Mandatory Node interview
      • 6.3.1.2. Minimum End User functionalities
      • 6.3.1.3. Node properties
      • 6.3.1.4. Additional Control requirements
        • 6.3.1.4.1. Removing associations
    • 6.3.2. Association Group Information (AGI) Command Class, version 1-3
      • 6.3.2.1. Mandatory node interview
      • 6.3.2.2. Minimum end user functionalities
      • 6.3.2.3. Node properties
    • 6.3.3. Battery Command Class, version 1
      • 6.3.3.1. Mandatory node interview
      • 6.3.3.2. Minimum end user functionalities
      • 6.3.3.3. Node properties
      • 6.3.3.4. Additional control requirements
    • 6.3.4. Device Reset Locally Command Class, version 1
      • 6.3.4.1. Mandatory node interview
      • 6.3.4.2. Minimum end user functionalities
      • 6.3.4.3. Node properties
      • 6.3.4.4. Additional control requirements
    • 6.3.5. Firmware Update Meta Data Command Class, version 1-6
      • 6.3.5.1. Mandatory node interview
      • 6.3.5.2. Minimum end user functionalities
        • 6.3.5.2.1. Firmware update
      • 6.3.5.3. Node properties
      • 6.3.5.4. Additional control requirements
    • 6.3.6. Indicator Command Class, version 1-3
      • 6.3.6.1. Mandatory node interview
      • 6.3.6.2. Minimum end user functionalities
        • 6.3.6.2.1. Identify
      • 6.3.6.3. Node properties
      • 6.3.6.4. Additional control requirements
    • 6.3.7. Multi Channel Association Command Class, version 2-5
      • 6.3.7.1. Mandatory node interview
      • 6.3.7.2. Minimum end user functionalities
      • 6.3.7.3. Node properties
      • 6.3.7.4. Additional control requirements
        • 6.3.7.4.1. Removing associations
    • 6.3.8. Time Command Class, version 1-3
      • 6.3.8.1. Mandatory node interview
      • 6.3.8.2. Minimum end user functionalities
      • 6.3.8.3. Node properties
      • 6.3.8.4. Additional control requirements
    • 6.3.9. Version Command Class, version 1-4
      • 6.3.9.1. Mandatory node interview
      • 6.3.9.2. Minimum end user functionalities
      • 6.3.9.3. Node properties
      • 6.3.9.4. Additional control requirements
    • 6.3.10. Wake-Up Command Class, version 1-2
      • 6.3.10.1. Mandatory node interview
      • 6.3.10.2. Minimum end user functionalities
      • 6.3.10.3. Node properties
      • 6.3.10.4. Additional control requirements
  • 6.4. Transport-Encapsulation Command Classes
    • 6.4.1. CRC-16 Encapsulation Command Class Control Definitions, version 1
      • 6.4.1.1. Mandatory node interview
      • 6.4.1.2. Minimum end user functionalities
      • 6.4.1.3. Node properties
      • 6.4.1.4. Additional Control Requirements
    • 6.4.2. Multi Channel Command Class, version 3-4
      • 6.4.2.1. Mandatory node interview
      • 6.4.2.2. Minimum end user functionalities
      • 6.4.2.3. Node properties
      • 6.4.2.4. Additional Control Requirements
        • 6.4.2.4.1. Root Device and End Point Command Classes
        • 6.4.2.4.2. S0 only Multi Channel nodes
        • 6.4.2.4.3. Association and Multi Channel Association mapping
    • 6.4.3. Security 0 Command Class
      • 6.4.3.1. Mandatory node interview
      • 6.4.3.2. Minimum end user functionalities
      • 6.4.3.3. Node properties
      • 6.4.3.4. Additional Control Requirements
    • 6.4.4. Security 2 Command Class
      • 6.4.4.1. Mandatory node interview
      • 6.4.4.2. Minimum end user functionalities
      • 6.4.4.3. Node properties
      • 6.4.4.4. Additional Control Requirements
    • 6.4.5. Supervision Command Class, version 1
      • 6.4.5.1. Mandatory node interview
      • 6.4.5.2. Minimum end user functionalities
      • 6.4.5.3. Node properties
      • 6.4.5.4. Additional Control Requirements
• 7. Device Type v2 specification
  • 7.1. Introduction
  • 7.2. Common Z-Wave Plus v2 Device Type Requirements
    • 7.2.1. How to detect Z-Wave Plus v2 compliant nodes
    • 7.2.2. Command Classes Support Requirements
      • 7.2.2.1. Root Device level
      • 7.2.2.2. End Point level
    • 7.2.3. Identify
    • 7.2.4. Dynamic Capabilities and Node Discovery
    • 7.2.5. Controller Functionalities
      • 7.2.5.1. Interoperability
      • 7.2.5.2. Minimal Control Functionality
    • 7.2.6. Command Class Support Specific Requirements
      • 7.2.6.1. Anti-theft Command Class
      • 7.2.6.2. Application Status Command Class
      • 7.2.6.3. Association requirements
        • 7.2.6.3.1. Mandatory groups
        • 7.2.6.3.2. Lifeline reports
      • 7.2.6.4. Configuration Command Class
      • 7.2.6.5. Firmware Update Meta Data Command Class
        • 7.2.6.5.1. SmartStart QR Code accuracy
      • 7.2.6.6. Wake Up Command Class
      • 7.2.6.7. Multi Channel support
      • 7.2.6.8. Security 2 Command Class
        • 7.2.6.8.1. S2 bootstrapping and functionalities
        • 7.2.6.8.2. S2 Security Classes requirements
        • 7.2.6.8.3. S0 Security Class requirements
        • 7.2.6.8.4. DSK format and representations
        • 7.2.6.8.5. Mandatory DSK representations
        • 7.2.6.8.6. Filtering Security Class for controlling nodes
        • 7.2.6.8.7. Controlling nodes: Security Class learning
    • 7.2.7. Command Class Control Specific Requirements
      • 7.2.7.1. Anti-Theft Command Class
    • 7.2.8. SmartStart Requirements
    • 7.2.9. Z-Wave Long Range Support
      • 7.2.9.1. Nodes supporting to be included with Z-Wave Long Range
      • 7.2.9.2. Nodes supporting to include using Z-Wave Long Range
    • 7.2.10. Required Documentation
      • 7.2.10.1. Terminology
      • 7.2.10.2. Additional documentation required for Z-Wave Certification
      • 7.2.10.3. Documentation for Classic Inclusion and Exclusion
      • 7.2.10.4. Documentation related to SmartStart
      • 7.2.10.5. Documentation related to devices from multiple manufacturers
      • 7.2.10.6. Documentation for Association Command Class
      • 7.2.10.7. Documentation for Configuration Command Class
      • 7.2.10.8. Documentation for Wake Up Command Class
      • 7.2.10.9. Documentation for Security 2 Command Class
      • 7.2.10.10. Documentation for Supervision Command Class
      • 7.2.10.11. Documentation for Basic Command Class
      • 7.2.10.12. Documentation for Notification Command Class
      • 7.2.10.13. Documentation for dynamic capabilities
      • 7.2.10.14. Documentation for Identity function
      • 7.2.10.15. Documentation for Z-Wave Long Range
        • 7.2.10.15.1. Nodes supporting to include using Z-Wave Long Range
  • 7.3. Z-Wave Plus v2 Device Type Definition
    • 7.3.1. Optional Command Classes
    • 7.3.2. Supporting Device Type Overview
    • 7.3.3. Controlling Device Type Overview
    • 7.3.4. From Z-Wave Plus to Z-Wave Plus v2 Certification
    • 7.3.5. Actuator Supporting Device Types
      • 7.3.5.1. Lock DT
        • 7.3.5.1.1. Generic and Specific Device Class
        • 7.3.5.1.2. S2 Security Classes
        • 7.3.5.1.3. Mandatory Command Classes
        • 7.3.5.1.4. Basic Command Class Requirements
      • 7.3.5.2. Motorized Barrier DT
        • 7.3.5.2.1. Generic and Specific Device Class
        • 7.3.5.2.2. S2 Security Classes
        • 7.3.5.2.3. Mandatory Command Classes
        • 7.3.5.2.4. Basic Command Class Requirements
      • 7.3.5.3. Color Switch DT
        • 7.3.5.3.1. Generic and Specific Device Class
        • 7.3.5.3.2. Mandatory Command Classes
        • 7.3.5.3.3. Basic Command Class Requirements
      • 7.3.5.4. Window Covering DT
        • 7.3.5.4.1. Generic and Specific Device Class
        • 7.3.5.4.2. Mandatory Command Classes
        • 7.3.5.4.3. Basic Command Class Requirements
      • 7.3.5.5. Thermostat DT
        • 7.3.5.5.1. Generic and Specific Device Class
        • 7.3.5.5.2. Mandatory Command Classes
        • 7.3.5.5.3. Basic Command Class Requirements
      • 7.3.5.6. Sound Switch DT
        • 7.3.5.6.1. Generic and Specific Device Class
        • 7.3.5.6.2. Mandatory Command Classes
        • 7.3.5.6.3. Basic Command Class Requirements
      • 7.3.5.7. AV Control Point DT
        • 7.3.5.7.1. Generic and Specific Device Class
        • 7.3.5.7.2. Mandatory Command Classes
        • 7.3.5.7.3. Basic Command Class Requirements
      • 7.3.5.8. Multilevel Switch DT
        • 7.3.5.8.1. Generic and Specific Device Class
        • 7.3.5.8.2. Mandatory Command Classes
        • 7.3.5.8.3. Basic Command Class Requirements
      • 7.3.5.9. Binary Switch DT
        • 7.3.5.9.1. Generic and Specific Device Class
        • 7.3.5.9.2. Mandatory Command Classes
        • 7.3.5.9.3. Basic Command Class Requirements
    • 7.3.6. Reporting Supporting Device Types
      • 7.3.6.1. Entry Control Keypad DT
        • 7.3.6.1.1. Generic and Specific Device Class
        • 7.3.6.1.2. S2 Security Classes
        • 7.3.6.1.3. Mandatory Command Classes
        • 7.3.6.1.4. Basic Command Class Requirements
      • 7.3.6.2. Multilevel Sensor DT
        • 7.3.6.2.1. Generic and Specific Device Class
        • 7.3.6.2.2. Mandatory Command Classes
        • 7.3.6.2.3. Basic Command Class Requirements
      • 7.3.6.3. Notification Sensor DT
        • 7.3.6.3.1. Generic and Specific Device Class
        • 7.3.6.3.2. Mandatory Command Classes
        • 7.3.6.3.3. Basic Command Class Requirements
      • 7.3.6.4. Meter Sensor DT
        • 7.3.6.4.1. Generic and Specific Device Class
        • 7.3.6.4.2. Mandatory Command Classes
        • 7.3.6.4.3. Basic Command Class Requirements
      • 7.3.6.5. Central Scene DT
        • 7.3.6.5.1. Generic and Specific Device Class
        • 7.3.6.5.2. Mandatory Command Classes
        • 7.3.6.5.3. Basic Command Class Requirements
        • 7.3.6.5.4. Recommended options
    • 7.3.7. Other Device Types
      • 7.3.7.1. Repeater DT
        • 7.3.7.1.1. Role Type
        • 7.3.7.1.2. Generic and Specific Device Class
        • 7.3.7.1.3. Mandatory Command Classes
        • 7.3.7.1.4. Basic Command Class Requirements
      • 7.3.7.2. IR Repeater DT
        • 7.3.7.2.1. Role Type
        • 7.3.7.2.2. Generic and Specific Device Class
        • 7.3.7.2.3. Mandatory Command Classes
        • 7.3.7.2.4. Basic Command Class Requirements
    • 7.3.8. Controlling Device Types
      • 7.3.8.1. Gateway DT
        • 7.3.8.1.1. Role Type
        • 7.3.8.1.2. Generic and Specific Device Class
        • 7.3.8.1.3. S2 Security Classes
        • 7.3.8.1.4. Mandatory Command Classes
        • 7.3.8.1.5. Recommended options
        • 7.3.8.1.6. Basic Command Considerations
      • 7.3.8.2. Generic Controller DT
        • 7.3.8.2.1. Generic and Specific Device Class
        • 7.3.8.2.2. Mandatory Command Classes
        • 7.3.8.2.3. Recommended options
        • 7.3.8.2.4. Basic Command Considerations
• 8. Role Type specification
  • 8.1. Introduction
    • 8.1.1. Purpose
  • 8.2. Z-Wave Compliance Overview
    • 8.2.1. SIS Assignment
      • 8.2.1.1. Non-SIS capable Primary Controllers
      • 8.2.1.2. SIS capable controllers
      • 8.2.1.3. SIS return route assignment
    • 8.2.2. Network Inclusion and Exclusion
    • 8.2.3. Security bootstrapping
      • 8.2.3.1. Security 0 Command Class
        • 8.2.3.1.1. Upgrading non-secure networks
      • 8.2.3.2. Security 2 Command Class
        • 8.2.3.2.1. Bootstrapping capabilities
        • 8.2.3.2.2. Granting Security Classes
        • 8.2.3.2.3. Informing the user about security
    • 8.2.4. Device Reset Locally support
    • 8.2.5. Node interview and response timeouts
    • 8.2.6. Polling Devices
      • 8.2.6.1. Polling with no errors
      • 8.2.6.2. Polling with transmit error
      • 8.2.6.3. Polling with missing Report Frame
    • 8.2.7. Unsolicited communication
      • 8.2.7.1. Unsolicited data collection communication
      • 8.2.7.2. Unsolicited control communication
    • 8.2.8. Runtime communication
      • 8.2.8.1. Routing
      • 8.2.8.2. Wake-Up communication timeout protection
    • 8.2.9. Network maintenance
    • 8.2.10. SmartStart requirements
      • 8.2.10.1. Support requirements
        • 8.2.10.1.1. SmartStart learn mode activation
        • 8.2.10.1.2. Higher Inclusion Request Interval
      • 8.2.10.2. Control requirements
        • 8.2.10.2.1. Command Class support
        • 8.2.10.2.2. User interface
        • 8.2.10.2.3. QR Code scanning capability
  • 8.3. Role Type Overview
    • 8.3.1. Detecting the Role Type of a device
  • 8.4. Role Type Definitions
    • 8.4.1. Central Static Controller (CSC)
      • 8.4.1.1. CSC Protocol Requirements
        • 8.4.1.1.1. If first node in the network
      • 8.4.1.2. CSC setup
        • 8.4.1.2.1. Inclusion process
        • 8.4.1.2.2. Lifeline configuration
        • 8.4.1.2.3. CSC including a SSC, PC, RPC or NAEN
        • 8.4.1.2.4. CSC including a PEN, LSEN, RSEN or WOEEN
        • 8.4.1.2.5. CSC including an AOEN
        • 8.4.1.2.6. CSC including another CSC
        • 8.4.1.2.7. CSC included by a PC, RPC, SSC
      • 8.4.1.3. CSC Runtime Configuration
      • 8.4.1.4. CSC Runtime Communication
    • 8.4.2. Sub Static Controller (SSC)
      • 8.4.2.1. SSC Protocol Requirements
        • 8.4.2.1.1. If first node in the network
      • 8.4.2.2. SSC Setup
        • 8.4.2.2.1. Inclusion process
        • 8.4.2.2.2. Lifeline configuration
        • 8.4.2.2.3. SSC including a CSC
        • 8.4.2.2.4. SSC including an RPC, PEN, RSEN or WOEEN
        • 8.4.2.2.5. SSC including an SSC, PC, AOEN, LSEN, or NAEN
      • 8.4.2.3. SSC Runtime Configuration
      • 8.4.2.4. SSC Runtime communication
    • 8.4.3. Portable Controller (PC)
      • 8.4.3.1. PC Protocol Requirements
        • 8.4.3.1.1. If first node in the network
      • 8.4.3.2. PC Setup
        • 8.4.3.2.1. Inclusion process
        • 8.4.3.2.2. Lifeline configuration
        • 8.4.3.2.3. PC including a CSC
        • 8.4.3.2.4. PC including an RPC, PEN, RSEN or WOEEN
        • 8.4.3.2.5. PC including an SSC, PC, AOEN, LSEN or NAEN
      • 8.4.3.3. PC Runtime Configuration
      • 8.4.3.4. PC Runtime communication
    • 8.4.4. Reporting Portable Controller (RPC)
      • 8.4.4.1. RPC protocol requirements
        • 8.4.4.1.1. If first node in the network
      • 8.4.4.2. RPC Setup
        • 8.4.4.2.1. Inclusion process
        • 8.4.4.2.2. Lifeline configuration
        • 8.4.4.2.3. RPC including a CSC
        • 8.4.4.2.4. RPC including an RPC, PEN, RSEN or WOEEN
        • 8.4.4.2.5. RPC including an SSC, PC, AOEN, LSEN or NAEN
      • 8.4.4.3. RPC runtime configuration
      • 8.4.4.4. RPC runtime communication
        • 8.4.4.4.1. Portable End Node (PEN)
    • 8.4.5. Portable End Node (PEN)
      • 8.4.5.1. PEN protocol requirements
      • 8.4.5.2. PEN setup
        • 8.4.5.2.1. Inclusion process
      • 8.4.5.3. PEN Runtime configuration
      • 8.4.5.4. PEN Runtime communication
    • 8.4.6. Always On End Node (AOEN)
      • 8.4.6.1. AOEN protocol requirements
      • 8.4.6.2. AOEN setup
        • 8.4.6.2.1. Inclusion process
      • 8.4.6.3. AOEN runtime configuration
      • 8.4.6.4. AOEN runtime communication
    • 8.4.7. Reporting Sleeping End Node (RSEN)
      • 8.4.7.1. RSEN protocol requirements
      • 8.4.7.2. RSEN setup
        • 8.4.7.2.1. Inclusion process
        • 8.4.7.2.2. RSEN runtime configuration
        • 8.4.7.2.3. RSEN runtime communication
    • 8.4.8. Listening Sleeping End Node (LSEN)
      • 8.4.8.1. LSEN Protocol Requirements
      • 8.4.8.2. LSEN Setup
        • 8.4.8.2.1. Inclusion Process
      • 8.4.8.3. LSEN Runtime Configuration
      • 8.4.8.4. LSEN Runtime Communication
    • 8.4.9. Network Aware End Node (NAEN)
      • 8.4.9.1. NAEN Protocol Requirements
      • 8.4.9.2. NAEN Setup
        • 8.4.9.2.1. Inclusion process
      • 8.4.9.3. NAEN Runtime Configuration
      • 8.4.9.4. NAEN Runtime communication
    • 8.4.10. Wake On Event End Node (WOEEN)
      • 8.4.10.1. WOEEN Protocol Requirements
      • 8.4.10.2. WOEEN Setup
        • 8.4.10.2.1. Mode Selection
      • 8.4.10.3. WOEEN Runtime Configuration
      • 8.4.10.4. WOEEN Runtime Communication
• 9. Appendices
  • 9.1. Appendix A ASCII CODES
  • 9.2. Appendix B CRC-CCITT Source Code
    • 9.2.1. Header file
    • 9.2.2. Implementation
  • 9.3. Appendix C Inclusion Process
    • 9.3.1. Being Included
    • 9.3.2. Including a Node
• 10. References